Hamworthy Merley Скачать руководство пользователя страница 66

Страница: 66 / 108

HAMWORTHY HEATING LTD

Merley Boiler Sequence Controller

500001210/D

Minimum limitation of the return temperature

Line no.

Operating line

3560

Return setpoint min

If the return temperature drops below the adjusted return setpoint, maintained boiler
return temperature becomes active..

Maintained boiler return temperature allows consumers to be influenced or a return
temperature controller to be used.

6.10 DHW storage tank

Charging control

Increase of the flow
temperature setpoint

Type of charging

The DHW request to the boiler is made up of the current DHW setpoint plus the
adjustable charging boost.

The storage tank can be charged using up to 2 sensors.

It is also possible to combine partial charging with 1 sensor and the legionella function

with 2 sensors (setting 3).

Electric immersion heater

Electric immersion heater
operating mode

Substitute

The electric immersion heater is only used if the boiler delivers a fault status message or

has been shut down via boiler lock. This means that in normal situations the DHW is

always heated by the boiler.

Summer

The electric immersion heater is used as soon as all connected heating circuits have

switched to summer operation. The DHW is again heated by the boiler as soon as at

least one of the heating circuits has switched back to heating operation. But the electric

immersion heater is also used if the boiler delivers a fault status message or has been

shut down via boiler lock.

Always

DHW is heated with the electric immersion heater throughout the year. This means that
when using this application, the boiler is never required for DHW heating.

Line no.

Operating line

5020

Flow setpoint boost

5022

Type of charging

With B3

With B3 & B31

With B3, legionella B3 & B31

Line no.

Operating line

5060

Immersion heater operating mode

Substitute

Summer

Always

5061

Immersion heater release

24/day

DHW release

Time program 4 / DHW

5062

Immersion heater control

External thermostat

2nd DHW sensor

Содержание Merley













































































































Результаты поиска

Содержание Merley

Отзывы:

Hamworthy Merley, Инструкция по установке, вводу в эксплуатацию и эксплуатации, Страница: 66 / 108

Результаты поиска

Содержание Merley

Отзывы: