background image

 

 

Hampshire Controls Corp. 

 

Revision 1.2 

Temperature Transmitter Operating Instruction 

Page 1 of 21 

 

©2014 

 

Limited Warranty 

 
 
 
Hampshire  Controls  Corporation  warrants  each  manufactured  item  against  defects  in  material 
and workmanship, when used as recommended, for a period of one year from original purchase. 
Products believed to have such defects must be returned to the factory by prepaid transportation. 
 
Hampshire Controls’ obligation under this warranty is limited to the repair or replacement, at its 
option, of those items which upon examination prove to be defective. Such repair or replacement 
will be made without charge. 
 
This  warranty  will  be  void  if  repairs  or  alterations  are  made  or  attempted  without  factory 
authorization; or if the item has been subject to misuse, negligence or accident. 
 
Hampshire  Controls  Corporation  assumes  no  liability  for  consequential  damages  of  any  kind. 
The purchaser, by acceptance of the product, assumes all liability of the consequence of its use or 
misuse. 
 
Hampshire  Controls  Corporation  makes  no  other  warranty,  whether  expressed  or  implied,  in 
connection with the sale or use of its products. 

Содержание TT Series























Отзывы: