Hammond A-3 Скачать руководство пользователя страница 75

Страница: 75 / 180

HA<O>

XK-5

Owner’s Playing Guide

Rotor

Speed:

Rise

Time

Fall

Time

Brake

Time

Mode:

SLOW

FAST

SLOW

FAST

STOP

Delay

Time

❹ / ⓭

SLOW SPEED - HORN / DRUM (L)

These allow you to set the rotor speed for the Slow or Chorale

mode.
The setting range is 0, 24 to 318 rpm.

❺ / ⓮

FAST SPEED - HORN / DRUM (L)

These allow you to set the rotor speed on the “FAST” or Tremolo

mode.
The setting range is 0, 375 to 453 rpm.

❻ / ⓯

RISE TIME - HORN / DRUM (L)

These allow you to set the time for the rotors to “ramp up” to the

“FAST” speed,when switching from “SLOW” or “STOP” to the

“FAST” mode.
The setting range for the Horn rotor is 0.2 to 5.0 sec., and the Bass rotor is 0.5 to 12.5 sec.

❼ / ⓰

FALL TIME - HORN / DRUM (L)

These allow you to set the time for the rotor to reach the ‘Slow Speed’, when switching from

“FAST” to “SLOW” mode.
The setting range for the Horn rotor is 0.2 to 5.0 sec., and the Bass rotor is 0.5 to 12.5 sec.

❽ / ⓱

BRAKE TIME - HORN / DRUM (L)

These allow you to set the time for the rotor to stop, when switching from “FAST” to the

“STOP” mode.
The setting range for the Horn rotor is 0.2 to 5.0 sec., and the Bass rotor is 0.5 to 12.5 sec.

❾ / ⓲

DELAY TIME - HORN / DRUM (L)

These allow you to set the time to the speed starts changing, when the mode

is switched.
The setting range is 0 to 0.8 sec.

❿ / ⓳

MIC WIDTH - HORN / DRUM (L)

These allow you to set the Virtual Leslie Speaker at which location the Micro-

phones should be placed.
“Width” sets the distance between the left and the right microphones. The

setting range is 0 to 40. The value increases makes wider stereophonic. At “0,”

mono.

⓫ / ⓴

MIC CENTER - HORN / DRUM (L)

These allow you to set the offset between the center of two microphones and

pivot of the rotor.
The setting range is -50 to +50 cm. The virtual Leslie speaker turns counter

clockwise for Horn rotor, and clockwise for Drum rotor. To emphasize the

‘upcoming’, set the ‘+’ value for Horn rotor, and ‘-’ value for Drum rotor.

⓬ / ㉑

MIC DISTANCE - HORN / DRUM (L)

These allow you to set the distance between the Virtual Leslie Speaker and the

microphones.
The setting range is 30 to 200 cm. The value decreases makes deeper effect.

㉒ / ㉓ / ㉔

LEVEL - SUB BASS / DRUM / HORN (L)

These allow you to set the volume levels of the each rotor and the sub bass sound not modu-

lated with the Drum rotor.
The setting range is -12 to 0 dB.

㉕

CROSSOVER

These allow you to is set the diverging point of the frequencies of the Sub Bass and the Drum

rotor respectively.
The setting range is 20 to 248 Hz. The higher the value rises, the more lowered are the

modulation effects of the Pedals.

Distanc

Sub Bass

Drum Rotor

Horn Rotor

Center

Width

Содержание A-3





















































































































































































Результаты поиска

Содержание A-3

Отзывы:

Похожие инструкции для A-3

Бренды по названию

Популярные бренды

Hammond A-3, Руководство по использованию

Результаты поиска

Содержание A-3

Отзывы:

Похожие инструкции для A-3

Бренды по названию

Популярные бренды