Hammond A-3 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 180

background image

HA<O>

XK-5

Owner’s Playing Guide

122

CONTROL Edit Menu

This Edit Menu allows you to select the parameters for the various controls that you prefer.

NOTE: Please insure that the Expression Pedal and Foot Switch are properly connected before adjusting their settings.

u

FOOT CONTROLLER

❶

FOOT CONTROLLER 1 - MODE

This allows you to select the function controlled by the device connected to the CTRL1 jack.

OFF:

Does not function.

EXPRESSION:

Select this option when an Expression Pedal is connected.

The options below are for a connected Foot Switch.

LESLIE S/F ALT, MOM, TRI

Switches the Leslie Effect among Slow, Fast and Stop.

ALT

- The Foot Switch switches back and forth between Leslie Slow and Fast Rotor Speeds.

Each time the Foot Switch is pressed and released, the Leslie Rotors will change speeds.,.

MOM

- The Foot Switch switches Leslie Rotor Speeds. When the Foot Switch is pressed and

held, the Leslie Rotors will go at Fast speed. When the Foot Switch is not engaged, the Leslie
Rotors go at Slow speed.

TRI

- The Foot Switch switches back and forth between Leslie Slow and Fast Rotor Speeds

similar to the ALT mode. Additionally, if the Foot Switch is pressed and held for longer than 1
second, the Leslie Rotors will go to the Off or Stop position.

GLIDE:

The Foot Switch will bend the pitch. The amount of pitch bend is determined by a parameter
setting.

PATCH FWD, REV:

Use the Foot Switch to move forward or backward through the Patches.

FAVORITE FWD, REV:

Use the Foot Switch to move forward or backward through the Patches.

SPRING:

The Foot Switch will add the sound of a spring-type Reverb unit being jostled.

DELAY TIME:

The Foot Switch will add the Delay effect. The delay time is set by the time interval of pressing
the Foot Switch (page 92).

MENU/EXIT







ENTER

or,

CONTROL

To locate this Menu, follow the steps below:

PATCH/FAVORITE FWD/REV

The [PRESET SELECTOR] Touch Buttons deter-
mine which part of the Patch/Favorite is se-
lected by the Foot Switch
If both [PRESET SELECTOR] Touch Buttons are
“ON,” Preset Keys “C” through “A” will advance,
after which the next Preset Bank starting with
the “C” Preset Key Will advance. (see the dia-
gram below).
If only the [LOWER] PRESET SELECTOR Touch
Button is “ON,” the Presets will advance from
“C” to “A,” then loop back to “C” again in the
same Bank. (See the lower line of the diagram
below.)

C C



D D



E F F



G G



A

C C



D D



E F F



G G



A

C C



D D



E F F



G G



A

Bank

F

Bank

F



Bank

E

C C



D D



E F F



G G



A

Bank

F

❶

❷

❸

❹

❺

❻

❼

❽

❾

❿

⓬

⓭

⓮

⓯

⓰

⓱

⓲

⓳

⓴

⓫

㉑

㉒

㉓

㉔

㉕

㉖

㉗

㉘

㉙

«
...
120
121
122
123
124
...
»

Содержание A-3





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A-3

Бренд: CAENels Страницы: 75

Бренд: Maico Страницы: 27

Бренд: Magnescale Страницы: 14

Бренд: Oceanic Страницы: 68

Бренд: Oceanic Страницы: 24

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Omega Страницы: 31

Бренд: LaserLiner Страницы: 52

Бренд: Veris Страницы: 8

VIBRO-KING P/N 053493

Бренд: Fender Страницы: 8

Бренд: ETI Страницы: 2

Бренд: Sonel Страницы: 84

Бренд: Parker Страницы: 16

Бренд: Waterproof Страницы: 51

Бренд: Hameg Страницы: 40

Бренд: Lutron Electronics Страницы: 23

Бренд: Proteus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды