Haier GE CDT800P2N0S1 Скачать руководство пользователя

Страница: 68 / 78

– 68 –

The Mid-Level Conduit supplies water from the

main conduit to the mid spray arm and bottle

wash feature (some models). All models have

adjustable racks. An adjustable conduit is used

to allow proper engagement of the main conduit

to the mid conduit in both rack positions.

The adjustable conduit has an internal check

valve to block wash water from exiting the wash

system, keeping water directed into the mid

spray arm. The middle conduit is replaced as an

assembly, and individual parts for the assembly

are not available separately.

Some models have a port on the right side to

allow water flow to the bottle wash feature.

Mid Conduit

Cover Gasket Check Valve

Main Conduit

Body

Bottle Wash Hose Cover

Bottle Wash Supply Hose

Mid Conduit Bottle Wash Port

Middle Conduits

Содержание GE CDT800P2N0S1















































































Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N0S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды