Haier GE CDT800P2N0S1 Скачать руководство пользователя

Страница: 28 / 78

– 28 –

Third Rack Brackets

To remove the brackets, the dishwasher must be

removed from installation.

1. Remove the basket and the frame.

2. Remove two 1/4-in. hex-head screws.

3. Remove the two mounting nuts.

4. Remove the bracket from inside the

dishwasher.

Third Rack Rail Rollers

are secured to the

bracket with T-20 Torx-head screws.

1/4" hex-head screws

Mounting nuts

Appearances may vary throughout this service

guide. Some models do not have all features

shown or may be different depending on the

model number.

The spray system Manifold is mounted to the

lower rack. A bellows seals the conduit to the

manifold.

To remove the silverware conduit, remove one

1/4-in. hex-head screw and pull the conduit to the

right.

Silverware Wash

Содержание GE CDT800P2N0S1















































































Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N0S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды