Haier GE CDT800P2N0S1 Скачать руководство пользователя

Страница: 2 / 78

– 2 –

Safety Information

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by

individuals possessing adequate backgrounds of electrical,

electronic, and mechanical experience. Any attempt to repair a

major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in

connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing

this product. If electrical power is required for diagnosis or test

purposes, disconnect the power immediately after performing the

necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to

complete a path to ground are removed for service, they must be

returned to their original position and properly fastened.

GE Appliances, a Haier Company

reproduced in whole or in part in any form without written

permission from GE Appliances, a Haier Company.

For Warranty Information:

1. Go to http://products.geappliances.com

2. Search the model number.
3. Click on the Literature tab.

4. Click on Use and Care Manual.

5. Locate the Warranty page.

Warranty

Содержание GE CDT800P2N0S1















































































Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N0S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды