Haier GE CDT800P2N0S1 Скачать руководство пользователя

Страница: 24 / 78

– 24 –

Tub Rollers

The tub rollers are attached to the tub with a

screw in each roller.

To Remove the Tub Rollers

1. Remove the upper rail by removing the rear

end cap.

2. Remove the T20 Torx screw securing each

roller to the tub.

Model GDF570SGJ upper rack rollers mounted

to the tub are permanently attached to a bracket

which is toxed/riveted to the tub assembly. These

rollers are non-replaceable.

Upper Rack

Two upper rack configurations are available,

depending on the model: Wheels on Rails or Full

Extension Rails.

Wheels on Rails

To remove the rack from the dishwasher, pull the

rail assembly out a few inches for easier access.

Pull the tab on the end cap to the center of the

dishwasher and pull the end cap off the rail.

The rack may now be removed.

Upper Rack Rollers and Brackets

The upper rack roller brackets are locked into

place with a clip. The clip must be removed to

remove the roller brackets from the rack. Press

in on the tab and lift the locking clip.

(

Continued next page

)

Tub

Thrust

Washer

Tub

Roller

T20 Torx Screw

Racks

Содержание GE CDT800P2N0S1















































































Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N0S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды