Haier GE CDT800P2N0S1 Скачать руководство пользователя

Страница: 55 / 78

– 55 –

Clear

Door Diagnostic Tool

The Clear Door (

Part #

: WX05X20002) provides

technicians with a tool to accurately diagnose

2012 and newer dishwashers. Viewing the

wash zones not only includes more accuracy, it

will reduce diagnostic time, reduce repeat calls

and will increase technician confidence. There

may also be situations where the clear door can

be used to show a consumer the dishwasher is

operating properly.

Poor wash results can be due to many different

things. The clear door allows operation and

visibility of spray arms including rotation, slow or

non-rotation, leaks between wash components,

restrictions and spray jet pattern.

Proper spray arm speeds have a tolerance of

+/- 5 RPM. The lower spray arm turns clockwise

at approximately 50 RPM. The mid spray arm

turns approximately 30 RPM counter-clockwise.

The upper sprayer cannot be counted but can be

viewed for proper operation.

To Use WX05X20002 Clear Door

Place the dishwasher in service mode to fill,

circulate and drain. Details on Consumer

Error Mode and Service Mode can be found

in dishwasher mini manuals and this service

guide. All models have the same entry

directions. Different controls have different

ways to communicate results and progress.

2. Remove the bottom rack for an unobstructed

view of the lower spray arm.

3. Enter Consumer Error Mode.

4. Enter Service Mode.

5. Open the dishwasher door all the way to 90

degrees.

6. Place the WX05X20002 Clear Door into the

tub opening starting at the bottom.

WARNING

: To prevent any damage, do not close

the dishwasher door when the clear door is in

use.

7. The clear door has a latch strike. When

pushed into the latched position, it will

activate the door switch assembly. The

dishwasher may not start if the door is

installed to low.

Initiate Fill; the dishwasher will fill for 60

seconds.

9. Initiate the circulate test to view the circulation

system in action.

10. Service mode will initiate a 2-minute circulate

test 30 seconds lower clockwise (CW), 2 to 3

seconds lower counter-clockwise (CCW) (will

not reach full speed unless dishwasher is in

a main wash cycle) and 30 seconds upper

spray system. This pattern will repeat.

11.

Use a flashlight for better visibility. Look

for leaks in all areas including between the

conduits and wash components.

12. Determine potential areas for further

inspection and diagnoses.

13. Initiate drain; the dishwasher will drain for

approximately 70 seconds.

14. Remove the WX05X20002 Clear Door.

15. Proceed with any inspections, diagnoses and

repairs as detailed in the

No Circulation and

Drain

flow chart. Some components may

cause different symptoms depending on the

severity of part failure.

Diagnostics

Содержание GE CDT800P2N0S1















































































Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N0S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N0S1

Отзывы:

Похожие инструкции для GE CDT800P2N0S1

Бренды по названию

Популярные бренды