Haier DW12-CBE6 IS, Руководство пользователя

Страница: 4 / 40

Loading the Dishwasher Loading the Dishwasher Loading the Dishwasher Loading the Dishwasher Loading the Dishwasher Starting the Appliance Starting the Appliance Starting the Appliance Starting the Appliance Starting the Appliance
Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged, which re-
sults in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washed. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
How to use the lower rack How to use the lower rack How to use the lower rack How to use the lower rack How to use the lower rack
We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The lower rack features fold down tine rows (see fig.A) so that
larger or more pots and pans can be loaded.
- The silverware basket can be doubled (see fig.B) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans and it can also be
placed in the upper rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Espe-
cially long utensils should be placed in the horizontal position at
the front of the upper rack.
How to use the upper rack How to use the upper rack How to use the upper rack How to use the upper rack How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height by using the knobs lo-
cated on both sides of the rack itself (see fig.C).
Adjust the upper basket to the higher level and you have more
space to accommodate those taller pans and trays in the bottom
basket.
Shelf Shelf Shelf Shelf Shelf
Lean tall glasses and those with long stems against the shelf-not
against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack.
The additional cup rack can be swivelled in or out as required(see
fig.D).
Knife rack Knife rack Knife rack Knife rack Knife rack
The knife rack clips onto the side of the top basket, giving you the
freedom to wash your large sharp knives separately and out of
harm’s way (see fig.E).
Lower Rack Lower Rack Lower Rack Lower Rack Lower Rack
Upper Rack Upper Rack
Upper Rack Upper Rack
Upper Rack
.6. .6. .6. .6. .6. .5. .5. .5. .5. .5.
GB GB
GB GB
GB GB GB GB GB GB
Starting a wash cycle Starting a wash cycle Starting a wash cycle Starting a wash cycle Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the ON-OFF button "A" lo-
cated on the control panel. The "B" indicator light will come on.
At this point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle Setting and Starting a wash Cycle
Setting and Starting a wash Cycle Setting and Starting a wash Cycle
Setting and Starting a wash Cycle
Choose the desired cycle by pressing the cycle selection button
"G". Each time it is pressed, one of the cycle indicator lights "F"
will begin to blink in succession.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con-
tained in this manual, especially when first using the appliance).
Close the door and then the wash cycle has begun and cannot
be modified. If necessary, read the paragraph entitled, "Cancel-
ling or modifying a cycle while underway. "The end of the cycle
will be signalled by six acoustic sound, and the indicator light "F"
will turn off.
Cancelling or modifying a cycle while underway Cancelling or modifying a cycle while underway Cancelling or modifying a cycle while underway Cancelling or modifying a cycle while underway Cancelling or modifying a cycle while underway
To modify or cancel the carrying out of a washing cycle (being
the door opened), it's necessary to reset the previous
programming, by holding pushed the programme selector button
“G” for at least 3 seconds, and the buzzer emits one short warn-
ing signal.
If the reset operation was successful, a drain phase is started.
Once the drain phase is ended, the dishwasher stands waiting
for a new programming.
Premise: A cycle that is underway can only be modified if it has
only been running for a short time.
Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the
case, the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").
To change the cycle currently underway, open the door and press
the ON-OFF button "A",follow the instructions contained in the
paragraph entitled, "Starting a wash cycle ","Setting and Start-
ing a Wash Cycle".
To set a new wash cycle, follow the instructions contained in the
paragraph entitled, "Setting and Starting a Wash Cycle".
If you forget to load some of the dishes... If you forget to load some of the dishes... If you forget to load some of the dishes... If you forget to load some of the dishes... If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door carefully
(in order to avoid being sprayed by hot water). When the door is
closed again, after 30 seconds the cycle will automatically re-
start at the point where it left off.
At the end of the wash cycle At the end of the wash cycle At the end of the wash cycle At the end of the wash cycle At the end of the wash cycle
The end of the cycle will be indicated by six acoustical signal,at
the same time the "F" indicator light will turn off. Open the door,
turn off the appliance using the ON-OFF switch and turn off the
water supply to the unit. Wait a few minutes before removing the
dishes so as to avoid handling them while still hot (when they are
more susceptible to breakage) and to get better drying results.
Setting The Start Delay Time Setting The Start Delay Time Setting The Start Delay Time Setting The Start Delay Time Setting The Start Delay Time
Open the door of the dishwasher partially. If the "J" button is
pressed (see, Close-up View" Control Panel"). The start time for
the wash cycle can be delayed for 2,4,6,8,10 or 12 hours.
Each time the button is pressed, the "I" light will blink indicating
the length of the delay.
After selecting the delay time, the wash cycle can be set, as
explained in "Starting a wash cycle..." , close the door and at this
point the delay period will begin to count down. During this pe-
riod the delay indicator light (I) will come on. At the end of the
delay time, the indicator will turn off and the cycle will start.
NOTE: NOTE: NOTE: NOTE: NOTE:
a) During the delay period, none of the settings can be modified.
If necessary, they can be cancelled by pressing press the ON-
OFF button "A" located on the control panel.
b) If the door is opened during the delay period, the clock will
stop the countdown. It will start again when the door has been
closed.
Wash Cycle Adjustment Buttons Wash Cycle Adjustment Buttons Wash Cycle Adjustment Buttons Wash Cycle Adjustment Buttons Wash Cycle Adjustment Buttons
“3 in 1” Button “3 in 1” Button “3 in 1” Button “3 in 1” Button “3 in 1” Button
This button (see "Close-up View - Control Panel", letter "C C C C C" ) , is
used for the customer useing the “ 3 in 1” detergent.
When using "3in1"combination products, the rinse-aid and salt
lights are no longer useful. It may be helpful therefore to switch
the rinse aid off (please note that only some dishwashers have
this facility) and selecting the lowest possible setting for water
hardness.
If you decide to switch to the use of a standard detergent system
we advise that you:
1:Refill both the salt and rinse aid compartments.
2:Switch the waterhardness setting to the highest possible posi-
tion and run for three normal cycles without a load.
3:Readjust the waterhardness setting again according to the
conditions for your region (For more information please refer to
your instruction manual).
Notice Notice Notice Notice Notice
Do not place the tablets in the tub or the cutlery basket as this
will result in poorer wash results. The tablets should be placed in
the detergent doser.
Load for 12 Standard Settings (for IEC-EN 50242 tests) Load for 12 Standard Settings (for IEC-EN 50242 tests) Load for 12 Standard Settings (for IEC-EN 50242 tests) Load for 12 Standard Settings (for IEC-EN 50242 tests) Load for 12 Standard Settings (for IEC-EN 50242 tests)
fig.C fig.C fig.C fig.C fig.C
fig.D fig.D
fig.D fig.D fig.D fig.E fig.E
fig.E fig.E
fig.E
fig.B fig.B fig.B fig.B fig.B
fig.A fig.A fig.A fig.A fig.A
A1 A2 A3
A4