manualshive.com logo in svg

Haag-Streit BX 900, Инструкция по эксплуатации, Страница: 19 / 28

Поделиться
Скачать
Haag-Streit BX 900 Скачать руководство пользователя страница 19

19

DEUTSCH

ENGLISH 

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

© HAAG‑STREIT AG, 3098 Koeniz, Switzerland ‑ HS‑Doc. no. 1500.7220449‑04090 – 2021 – 08

(Table b)

Magnification at chip level Object size with chip size 15 × 22.4 mm

6.3 ×

0.63 ×

23.2 × 34.6 mm

10 ×

1 ×

14.6 × 21.9 mm

16 ×

1.6 ×

9.3 × 13.8 mm

25 ×

2.5 ×

5.8 × 8.7 mm

40 ×

4 ×

3.7 × 5.5 mm

Field of view of the object

Circle:

The field of view of the object observed through the microscope's

eyepiece.

Rectangle: Area of photograph.

8.7 Lens barrel

Focal length:

f 170 mm

8.8 Camera

NOTE!

The camera is to be set to a shutter time of 1/60 s in MANUAL operating

mode. The instruction for use for the camera must be followed for this

purpose.

9 Maintenance

WARNING!

• Do not modify this device without authorization of the manufacturer.

Installation and repairs may only be performed by trained

specialists.

• Contact your Haag-Streit representative for installation, repairs and

modification work on the system. The contact details are available at

www.haag-streit.com.

• Only original Haag-Streit spare parts may be used.

The LED illumination can be operated maintenance-free for its entire service life.

9.1 Device inspection

In order to correctly check the slit lamp, proceed as follows:

• Insert the test rod into the radial movement bearing, whilst at the same time

aligning the surface to the microscope at a right angle.

• Set the slit length to 8 mm.

• Set the illumination intensity to 50%.

• Set the magnification in the microscope to max.

• Set the eyepieces in such a way that the test rod is in sharp focus. In doing so,

turn the ocular from the (+) to the (-) side.

• For all magnifications, the structure of the test rod must be shown in sharp

focus.

• Close the slit edges to approx. 0.5 mm. The edges must be shown in sharp

focus.

• Open the slit edges completely and turn the test rod by 45°, the sharp area must

be in the centre of the test rod.

9.1.1 Testing the flash unit

In order to test the flash, press the release button (44) or the test button (47).

Содержание BX 900





























Отзывы:

Нет отзывов