manualshive.com logo in svg

Haag-Streit BX 900, Инструкция по эксплуатации, Страница: 13 / 28

Поделиться
Скачать
Haag-Streit BX 900 Скачать руководство пользователя страница 13

13

DEUTSCH

ENGLISH 

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

© HAAG‑STREIT AG, 3098 Koeniz, Switzerland ‑ HS‑Doc. no. 1500.7220449‑04090 – 2021 – 08

4.2 Setting the weight compensation facility

Turn the control lever (27) to its lowest position and then slacken it slightly by a

quarter turn. Swivel the microscope and illumination to the side. Apply 1-3 springs

depending on the accessory.

4.3 Switching on the compensation facility

Turn anticlockwise until the screws (12) are completely released.

4.4 Switching off the compensation facility

Turn the screws (12) clockwise until you meet resistance. Verify whether the

microscope arm springs back downwards if you push it upwards with your hand.

This will only happen if the load is already at maximum. Generally, as many

counterbalance springs should be deactivated as necessary until this spring action

occurs. The weight compensation facility is set correctly once the illumination and

microscope with the mounted accessories weigh slightly more than the

counterbalance springs.

4.5 Regulating the clearance of the slit width controls

The small screw in the centre of the right control knob (A)

allows you to regulate the friction of the turning movement

of these adjusting knobs. Turning it slightly to the right (in)

makes it harder, turning it left (out) makes it easier. It

should at least be set so hard that the slit cannot close on

its own.

4.6 Attaching/removing a camera

78. Lens barrel

79. Mirror and diaphragm component

80. Camera

81. Eyepiece

Remove the camera cover, attach the spacer ring to the camera and place the

camera on the lens barrel. If the camera is removed, the connection to the lens

barrel should be closed off with the cap intended for this purpose.

NOTE!

Consult your Haag-Streit representative for information on the supported

cameras and their connection rings.

5 Commissioning

Connect the PS-LED power supply and FU 01 flash unit to the mains.

5.1 Switching on the device

• Throw the rocker switch on the PS-LED power supply and the main switch on

the FU 01 flash unit 01 I = ’ON’. The green lamps in the rocker switches light up

when the device is switched on.

• Turn the rotating knob on the illumination control to a position between '1' and

'10'.

Содержание BX 900





























Отзывы:

Нет отзывов