background image

 

2-4 

SN

 

Item

 

Requirements

 

Power 
grounding 
(AC)

 

z

 

Use a power cord with a protective earth (PE). Do not use a power cord with 
only an L line and an N line. 

z

 

The neutral line of the power cord should not be connected with the PGND of 
other communications equipment. The L and N lines cannot be connected 

 

Lightning 
arrester

 

In plain areas, the protection angle of the lightning rod should be less than 45 
degrees. In mountainous areas or lightning areas, the protection angle should 
be less than 30 degrees. The lightning protection grounding (for example, the 
grounding of the lightning rod) should be connected to the earthing conductor of 
the equipment room.

 

6 Feeder

 

z

 

The antenna support is already prepared according to the design 
requirements. 

z

 

A feeder lightning rod is already installed and grounded according to the 
design requirements.

 

Outdoor 
lightning 
arrester  

Power lightning arrester, port lightning protector, and feeder lightning arrester 
are recommended for outdoor installations. The power lightning arrester and the 
feeder lightning arrester should be near the AP, and the network interface 
lightning arrester should be near the peer device of the AP. The network 
interface lightning arrester should be installed where the network cable is just 
led out of the room. 

Network 
cable 

Use a shielded twisted pair cables for an AP used outdoors. Ensure that the 
devices at the two ends of the cable are well grounded. 

 

After you have completed the preparations, you can start installing the AP. The installation of indoor 
models is different from that of the outdoor models. For details, refer to 3  “Installation of Indoor APs” on 
page 3-1 and 4  “Installation of Outdoor APs” on page 4-1. 

 

Содержание WA2210-AG_INDOORSINGLEBANDAP














































Отзывы: