GYS 014657, Руководство пользователя

Страница: 20 / 92

20
PROGYS 220E FV CEL
EN
WELDING PARAMETERS
WELDING INTENSITY SETTINGS
The following settings concern the intensity range that may be used depending on the electrode’s type and diameter . These ranges are quite large
as they depend on the application and the welding position.
Ø electrode (mm) Rutile E6013 (A) Basic E7018 (A) Cellulosic E6010 (A)
1.6 30-60 30-55 -
2.0 50-70 50-80 -
2.5 60-100 80-110 60-75
3.15 80-150 90-140 85-90
4.0 100-200 125-210 120-160
5 150-220 200-220 110-170
ARCFORCE SETTINGS
It is recommended to set the arc force in median position (0) to start the welding and adjust it according to the results and welding preferences.
Note : the arcforce setting range is specific to the selected electrode type.
ADVANCED SETTINGS
Refer to the chapter « menu access » for more details regarding welding parameters.
The two MMA modes and come with the following additional settings :
: Hotstart Time, duration of the extra current at arc strike, expressed in seconds.
: Antisticking, active (On), the current will stop after 2 consecutive seconds of short circuit, inactive (Off), the current will not stop, even in
the event of long short circuit.
In MMA vertical up mode , two extra settings are available :
: Frequency, determines the number of pulses per second (Hz).
: Percentage, determines the background/cold current expressed in percentage of the welding current.
: Duty cycle, determines the duty cycle expressed as a percentage of the pulsation frequency.
TUNGSTEN ELECTRODE WELDING WITH INERT GAS (TIG AND TIG VERTICAL UP
Pulse
)
CONNECTIONS AND RECOMMENDATIONS
TIG welding requires a torch as well as a gas bottle equipped with a regulator.
Connect the earth clamp to the positive connector (+).
Connect the torch’s earth cable to the negative plug (–).
Connect the torch’s gas hose to the regulator’s output.
Ensure that the torch is equipped and ready to weld, and that the consumables (Vise grip, ceramic gas nozzle, collet and collet body) are not damaged.
Rutile
6013
Basic
7018
Cellulosic
6010
MMA
press 3 s
TIG

Pulse Pulse
MODE
HOT START
ARC FORCE
A
V
VRD
setup
memory
press 3s press 3s
BLANC / WHITE
COULEURS / COLORS :
CLAVIER MMA 200 A 125 x 90 mm
2018/11/08
PANTONE 427C
PANTONE 429C
NOIR / BLACK
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE-DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
I N V E R T E R
W E L D E R
Rutile
6013
Basic
7018
Cellulosic
6010
MMA
press 3 s
TIG

Pulse Pulse
MODE
HOT START
ARC FORCE
A
V
VRD
setup
memory
press 3s press 3s
BLANC / WHITE
COULEURS / COLORS :
CLAVIER MMA 200 A 125 x 90 mm
2018/11/08
PANTONE 427C
PANTONE 429C
NOIR / BLACK
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE-DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
I N V E R T E R
W E L D E R
TIG
The grey areas are not useful for this mode.
TIG (TIG VERTICAL UP)
The grey areas are not useful for this mode.
SELECTION MODE
TIG
Press button
MODE
several times until the LED lights up under the symbol .
TIG PULSE
Press button
MODE
several times until the LEDs light up under the symbol and to the left of the symbol
Pulse
.
The pulsed TIG mode adds current pulsation to facilitate the welding of thin sheets while limiting temperature rise.