GYS 014657, Руководство пользователя

Страница: 19 / 92

19
PROGYS 220E FV CEL
EN
USE WITH EXTENSION CABLES
All extension cables must have an adequate size and section, relative to the machine’s voltage .
Use an extension that complies with national safety regulations.
Current input
Length - Extension selection
< 45m < 100m
230V 2.5 mm²
110V 2.5 mm² 4 mm²
ELECTRODE WELDING (MMA AND MMA VERTICAL UP )
CONNECTIONS AND RECOMMENDATIONS
• Connect the cables, electrode holder and earth clamp in the connectors,
• Respect the welding polarities and intensities indicated on the electrodes boxes,
• Remove the electrode from the electrode holder when the machin is not in use.
• Your machine is equipped with 3 specific functions to Inverters :
- The Hot Start increases the current at the beginning of the welding.
- The Arc Force increases the current in order to avoid the sticking when electrode enters in melted metal.
- The Anti Sticking allows you to easily withdraw your electrode without damaging it in case of sticking.
Rutile
6013
Basic
7018
Cellulosic
6010
MMA
press 3 s
TIG

Pulse Pulse
MODE
HOT START
ARC FORCE
A
V
VRD
setup
memory
press 3s press 3s
BLANC / WHITE
COULEURS / COLORS :
CLAVIER MMA 200 A 125 x 90 mm
2018/11/08
PANTONE 427C
PANTONE 429C
NOIR / BLACK
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE-DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
I N V E R T E R
W E L D E R
Rutile
6013
Basic
7018
Cellulosic
6010
MMA
press 3 s
TIG

Pulse Pulse
MODE
HOT START
ARC FORCE
A
V
VRD
setup
memory
press 3s press 3s
BLANC / WHITE
COULEURS / COLORS :
CLAVIER MMA 200 A 125 x 90 mm
2018/11/08
PANTONE 427C
PANTONE 429C
NOIR / BLACK
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE-DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
I N V E R T E R
W E L D E R
MMA
The grey areas are not useful for this mode.
MMA VERTICAL UP
The grey areas are not useful for this mode.
SELECTION MODE
MMA
Press button
MODE
several times until the LED lights up under the symbol .
MMA PULSE
Press button MODE several times until the LEDs light up under the symbol and to the right of the symbol
Pulse
.
The MMA vertical up mode adds a current pulse which makes vertical up welding easier.
MAIN SETTINGS
1. Selection of the type of coating
Select the electrode coating type by holding button
MODE
for more than 3 seconds until the LED lights up under the desired electrode type.
2. Setting the welding current
Adjust the welding current using the main knob according to the electrode diameter and the type of connection to be made. The current selected is
indicated on the display.
3. Adjusting the Hotstart level
Press button until the LED lights up to the left of the symbol
HOT START
.
Adjust the Hotstart level using the main control wheel, which is expressed as a percentage of the current selected. The Hotstart level is indicated on
the display.
4. Adjusting the Arcforce level
Press button until the LED lights up to the left of the symbol
ARC FORCE
.
Adjust the Arcforce level using the main dial, which is indexed from -10 to +10. The lower the Arcforce level, the softer the arc, the higher the Arcforce
level and the higher the welding overcurrent. The default value is 0.