GW Instek LCR-6000 Series Скачать руководство пользователя страница 48

Страница: 48 / 143

Measure Key

4.3.3 List Measurement Parameters

The list parameter used for the list measurement can be

the measurement frequency or the signal level [V/A].
Use the list point field to specify the list measurement

parameter.

To specify the list sweep measurement parameter

Step 1.  Press the [Measure] key.
Step 2.  Press the [LIST SETUP] soft-key.
Step 3.  Use the cursor key to select FREQ or VOLT

or CURR field.

Step 4. Use the soft-keys to select list measurement

parameter.

Soft-key

Function

FREQ

Uses frequency as the list
measurement parameter

VOLT

Uses voltage as the list measurement

parameter

CURR

Uses current as the list measurement

parameter

4.3.4 List Point and Limit Modes

The List measurement feature supports up to 10 list

points as well as measurement limit values. Each list

point can be turned on or off.

To configure the list points:

Step 1.  Press the [Measure] key.
Step 2.  Press the [LIST SETUP] soft-key.
Step 3.  Use the cursor key to select one of the list

point field (1 through 10)

Step 4. Use the soft-keys to turn on/off the current

point.

Soft-key

Function

Turn on current point

OFF

Turn off current point

Содержание LCR-6000 Series
















































































































































Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды

GW Instek LCR-6000 Series, Руководство пользователя

Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды