GW Instek LCR-6000 Series Скачать руководство пользователя страница 39

Страница: 39 / 143

LCR-6000 Series User Manual

SAVE TO USB Saves the recorded readings in the

buffer to an external USB flash drive.

The internal buffer is cleared after this
operation.

CLEAR

BUFFER

Clears the internal buffer.

SAVE & STOP Stops the recording and saves the

recorded readings in the internal
buffer to an external USB flash drive.

The internal buffer will be cleared

after the save operation.

If an external USB flash drive is not
plugged in, the meter will not stop the

ongoing recording.

CLEAR &
STOP

Stop recording and clears the internal
buffer.

Step 5. When the internal buffer is full, “!FULL” will

be added after the number of recorded

counts(in the [LOG] status field). The

following two operations are available in this
situation:

Soft-key

Function

SAVE TO USB Saves the recorded readings in the

buffer to an external USB flash drive.
The internal buffer is cleared after this

operation.

CLEAR
BUFFER

Clears the internal buffer.

Содержание LCR-6000 Series
















































































































































Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды

GW Instek LCR-6000 Series, Руководство пользователя

Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды