GW Instek LCR-6000 Series Скачать руководство пользователя страница 42

Страница: 42 / 143

Measure Key

4.2.1 Open Correction [OPEN]

The LCR-6000 Series’ OPEN correction capability

cancels errors due to the stray admittance (G, B) in
parallel with the device under test (Refer to Figure 4-3).

Figure 4-3

Stray Admittance

The OPEN correction data is taken at all preset

frequency points, independent of the test frequency you

set. Refer to the tables on page 128 for the trimming

frequency point lists for each model.

To perform open correction

Step 1.  Press the [Measure] key.
Step 2.  Press the [OPEN SHORT] soft-key.
Step 3.  Use the cursor key to select the [OPEN] field.

Soft-key

Function

Enables open correction.

OFF

Disables open correction.

MEAS OPEN

Starts open correction (AC).

DCR OPEN

Starts open correction (DC).

Step 4. Press the [MEAS OPEN] or [DCR OPEN]

soft-key. A dialog message, “Open-circuit the

test terminals” will appear.

Step 5. Connect the test fixture to the BNC terminals.

Do not connect the DUT to the fixture.

Step 6. Press the [OK] soft-key. The LCR-6000 will

then measured the open admittances

(capacitance and conductance) at the all test

frequency points.

Содержание LCR-6000 Series
















































































































































Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды

GW Instek LCR-6000 Series, Руководство пользователя

Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Похожие инструкции для LCR-6000 Series

Бренды по названию

Популярные бренды