GUDEL NGHP Series Скачать руководство пользователя страница 33

Страница: 33 / 146

Transport

The product is transported by air, land, or water. The packaging depends on
the mode of transport.

Truck

Shipped on a transport pallet

Aircraft

Shipped in a crate

Ship

Shipped in a case or container

Only perform the tasks described in this chapter after you have read and un-
derstood the chapter "Safety".

It concerns your personal safety!

WARNING

Ripping of lifting belts

The sharp edges cut the lifting belts. This can lead to severe or fatal injuries!

• Always protect the lifting belts with an edge guard

WARNING

Suspended loads

Improper handling of suspended loads can lead to severe injuries or death!

• Use appropriate lifting units

• Wear appropriate protective clothing

• Always keep sufficient distance from suspended loads

• Never enter the area below a suspended load

NOTE

Improper transport

Improper handling of the crates can lead to transport damage!

• Do not tip over the crates

• Avoid heavy vibrations and shocks

• Observe the symbols on the packaging

Transport

SERVICE MANUAL Planetary gear Güdel NRH, NRHP,
NGHP

18014399245011339_v2.0_

EN-US

Содержание NGHP Series



















































































































































Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды

GUDEL NGHP Series, Руководство по обслуживанию

Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды