GUDEL NGHP Series Скачать руководство пользователя страница 116

Страница: 116 / 146

Decommissioning, storage

9.1

Introduction

Only perform the tasks described in this chapter after you have read and un-
derstood the chapter "Safety".

It concerns your personal safety!

9.1.1

Personnel qualifications

Only appropriately trained and authorized technicians are allowed to work on
the product.

9.2

Storage conditions

CAUTION

Leaking fluids

During storage, substances that are hazardous to the environment can leak!

• Hazardous substances must be prevented from entering the drinking water

supply. Take appropriate measures

• Observe the country-specific safety data sheets

• Oils and greases must be disposed of as hazardous waste, even if the total

quantity is small

Room

Store the product in a dry location. For information on the required space
and the floor capacity, refer to the layout. Use a covering to protect the
product against dust and dirt.

Temperature

The ambient temperature must remain between -10 and +40 °C. Make sure
that the product is not subjected to great temperature fluctuations.

Air humidity

The air humidity must be below 75%.

Decommissioning, storage

SERVICE MANUAL Planetary gear Güdel NRH, NRHP,

NGHP

18014399245011339_v2.0_

EN-US

116

Содержание NGHP Series



















































































































































Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды

GUDEL NGHP Series, Руководство по обслуживанию

Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды