GUDEL NGHP Series Скачать руководство пользователя страница 74

Страница: 74 / 146

7.1.1

Safety

Only perform the tasks described in this chapter after you have read and un-
derstood the chapter "Safety".

It concerns your personal safety!

WARNING

Automatic startup

During work on the product, there is danger of the machine starting up auto-
matically. This can lead to severe or fatal injuries!

Before working in the danger area:

• Secure vertical axes (if equipped) against falling.

• Switch off the superordinate main power supply. Secure it against being

switched on again (main switch for the complete system)

• Before switching on the system again, make sure that no one is in the dan-

ger area

WARNING

Slipping hazard

Liquids run out if there is a leak. Persons may slip and injure themselves seri-
ously!

• Take application-specific protective measures

• Repair any leaks promptly

• Prevent any new leaks. Replace or modify the leaking component or as-

sembly

• Check the fill level and refill if necessary

WARNING

Falling axes, workpieces

Falling axes or workpieces can cause physical damage, serious or fatal injuries!

• Set down any workpieces before working in the danger area

• Never enter the area below suspended axes and workpieces

• Secure suspended axes using the stipulated equipment

• Check the belts of the telescope axes for signs of breakage and tears

Maintenance

SERVICE MANUAL Planetary gear Güdel NRH, NRHP,

NGHP

18014399245011339_v2.0_

EN-US

Содержание NGHP Series



















































































































































Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды

GUDEL NGHP Series, Руководство по обслуживанию

Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды