•
If the machine is turned off, remove the chips by a
brush.
•
Before starting the work check the function of safety
devices.
•
Do not overload the machine. It works better within the
stated output power range.
•
Use the right machine and make sure that the tools
(turning tool, driller, etc.) are not blunted or damaged
otherwise.
•
Always place cables behind the machine. Protect them
from heat, oil and sharp edges.
•
Before repair and maintenance and when not in use
unplug the cord.
•
Works on electric devices can be done by professional
only. Only original spare parts can be used.
•
Tidy work place makes work easier.
•
Be careful what you are doing. Use common sense.
•
Ensure that the machine base can carry its weight and
is stabile enough. Vibrations must be avoided while in
operation.
•
All parts were greased as an anticorrosive protection
in the workshop. Clean the machine before use with
ecological cleaning detergent.
•
Close the safety guard of jaw chuck
absolutely before start up of the machine.
•
Do not process hazardous or dusty materials like
wood, Teflon, etc.
•
Do not use the machine close to the flammable fluids
or gases.
•
Use the machine in suitable areas and do not expose
it to wet or humidity.
•
Ensure proper lighting when working.
•
Do not pull the power cord to unplug.
•
Make sure that the workpiece is always fastened
properly when processing. Fix it in vice or by using
clamping clips.
•
Always use clean and sharp tools.
•
When in dangerous situation, turn the machine off and
unplug it.
•
When damaged, the machine cannot be operated and
must be unplugged.
You can use inserting tools and
accessories approved by manufacturer only. Using
of unapproved parts bears great risk of injury.
•
Keep your workplace clean and tidy. Messy workplace
can cause accidents.
•
Always wear safety goggles when operating the
machine. If the work generates dust, dust mask is
recommended.
•
Chuck keys and other tools must be removed before
start up of the machine.
Use the shift bar to adjust revolutions only
when the machine is on hold!
Emergency Action
Apply the first aid adequate to the injury and get qualified
medical assistance as quickly as possible. Protect the
injured person from more accidents and calm him/her
down.
For the sake of eventual accident, in accordance with
DIN 13164, a workplace has to be fitted with a first-aid
kit. It is essential to replace any used material in the
first-aid kit immediately after it has been used. If you
seek help, state the following pieces of information:
1. Accident
site
2. Accident
type
3. Number of injured persons
4. Injury
type(s
Using the machine for intended use only
This machine is designed for drilling, deep and end milling of
small workpieces (max. dimensions: 300 mm x 200 mm x 200
mm) made of metal, plastic and similar materials. Serial chuck
with ring gear can be used only with drills and mills with
cylindrical shank of max. 16mm. when working metal (ST37),
the tool diameter cannot exceed 13mm. It is also possible to fix
tools with conical shank directly into working spindle (MK3).
This drill and mill is designed for domestic use only and cannot
be used industrially. Machine can be used for intended use
only. Any other use of the machine contradicts its design.
Residual risk and safety measures
Direct electric contact
Defected power cord or plug can cause electric shock.
Defected cords and plugs must be replaced by qualified person.
Use the machine only with residual current device (RCD)
connected.
Indirect electric contact
Injuries caused by conductive machine parts when the
machine is opened or in case of design errors.
Always plug the cord out when maintaining.
Use the machine only with residual current device (RCD)
connected
Insufficient local lighting
Insufficient lighting means great safety risk.
Always arrange proper lighting when working with the machine.
Disposal
Disposal instructions are made clear in pictograms on machine
label resp. package. You can find pictograms description in
chapter “Labeling”.
Disposal of transport package
Package protects machine against damage during the
transport. All packing materials are chosen to comply with strict
environmental waste disposal standards and can be therefore
recycled.
Recycling saves resources and minimizes waste existence.
Parts of the packing material can be dangerous to children (e.g.
plastic wrap, styropor). Risk of suffocation!!!
Package parts keep away from children and dispose it as soon
as possible.
Operation requirements
Operating personnel must read the manual carefully before use.
Qualification
There is no need for any special qualification except for detailed
training by qualified person.
Minimum age
Operate the machine can only people 18+ years old familiar
with manipulation and all functions of the machine. Youth
between 16 and 18 years can operate the machine only under
the supervision of an adult.
Exception is made when using by youths during the
occupational training to achieve exact skills under the
supervision of a trainer.
Training
There is a corresponding course needed only to operate this
machine. No special training is necessary.
14