Disposal
Instructions for disposal result from icons on the device,
or more precisely, on the package. Description of each
meaning can be found in the “Marking“ chapter.
Operating Staff Requirem ents
The operating staff must thoroughly read the operating
instructions before using the machine.
Qualification
No additional qualification is needed for using the device
apart from detailed training by a person w ith expert
know ledge.
Minim um Age
The device may only be operated by persons that have
reached 16 years of age.
An exception includes device use by juveniles w ithin job
preparation for purpose of reaching skills under
instructor's supervision.
Training
Appropriate training is only needed for device use. No
special training is necessary.
Transportation and Storage
•
If the device is stored for a longer period of time it
needs to be thoroughly cleaned and stored so that it
w as not accessible to unauthorised persons.
•
The compressor must never be stored or transported
laying or under pressure!
•
Pressure in the air jet may be reduced at
compressed air cooling.
Assembly / First Putting into Operation
If the compressor is supplied w ithout w heels assemble it
w ith a screw w rench according to
pic. 2
. The sequence of
screw s, nuts and w ashers is evident from
pic. 2
. In case
of need, a rubber foot also needs to be screw ed on.
Jointing materials, such as screw s, nuts, etc. are included
in the supply.
Transport stopper of the oil tank needs to be
exchanged for throat for oil adding and correct oil
level needs to be ensured (see the "Handling Throat
for Oil Adding and Oil Level Inspection" chapter)
before putting the compressor into operation)
Check the oil level at every startup!!!
Handling
Pull the connector plug out of socket before
each m aintenance, arrangement and adjustment of
the com pressor.
Working Pressure Adjustment
•
The w orking pressure may be adjusted very easily:
By turning the knob (2) in the
+ direction the
w orking pressure increases
. By turning the knob
in the
– direction the w orking pressure reduces.
The w orking pressure may be locked by tightening the
snap ring.
•
The com pressor is equipped w ith an autom atic safety
valve releasing pressure at overpressure. You m ay
release pressure from the air jet m anually by pulling
the valve ring (10).
ATTENTION:
Realise the amount of compressed air you w ill need from the
device! The pressure itself, how ever, is NOT decisive for perfect
and sufficient operation. Short sw itching the compressor on after
a long break w ithout use is common!
Have any repairs executed exclusively at qualified specialists.
Turn the com pressor never about the power,
otherwise no discharge of the unit is done. Without
discharge, the electric m otor through the back pressure
dam age!
Throat for Oil Adding and Oil Level Inspection
Transport stopper needs to be exchanged for throat
for oil adding and correct oil level needs to be ensured
before putting the compressor into operation.
Check the oil level at every startup!!!
Oil change
Since arriving on the piston can chip, it is absolutely
necessary after the first 10 hours of operation to carry out an
oil change. We recom mend that you are our com pressor
(SKU: 40056). Later, depending on the operation of the
com pressor, all 100 to 200 hours of operation an oil change
place. In order to carry out oil changes, open the drain screw
(16) and begin the process of w aste oil in a suitable
container.
Observe strictly the rules for disposal of w aste oil and
dispose of it properly in a w aste oil collection center.
Unscrew the drain screw is now firmly back on and fill oil up
to the m ark on the dipstick
In w inter we recommend a lubricity oils to start during
the cold season to help!
Air-pressure switch:
The compressor is equipped w ith an automatic air-pressure
sw itch that w ill sw itch the compressor off after reaching the upper
limit of the operating pressure and sw itch it on again w hen air is
needed. Starting pressure of 8 bar, max. pressure of 10 bar.
Inspections and Maintenance
Pull the connector plug out of socket before each w ork on the
machine. If you are not going to use the device for a longer period
of time w e recommend dropping a few oil drops at the place of air
filter insertion so that w alls of cylinders w ere lubricated at next
compressor sw itching on.
•
Use a damp cloth for cleaning of plastic parts. Do not use
cleaners, solvents or sharp objects.
•
Clean the air holes and mobile parts w ith a soft brush off the
settled dust after each use.
•
Regularly paint all metal parts w ith oil.
13
