background image

rev 06.13.12

 

  

15

Step 3

Lay the low voltage wire in a trench following a path from the 

selected electrical outlet to the control box. Wires coming up 

from the ground should be run through PVC conduit to protect 

them from lawn mower blades, weed eaters, and grazing 

animals. Bury the wire in the trench.

Step 4

Bring enough wire up 

through the PVC conduit to 

reach the control board.

Step 5 

Strip 

3

/

16

" off the ends of the low voltage wire and twist 

tightly. Attach these ends to the 14VAC OR SOLAR 

terminals located on the terminal block). Be certain not 

to let the exposed wires touch each other!
Insert one transformer wire into a 14VAC OR SOLAR 

terminal. Insert the other transformer wire into the 

remaining 14VAC OR SOLAR terminal. The transformer 

wires can be connected to the 14VAC OR SOLAR 

terminals regardless of color/polarity.
Tighten set screws against exposed end of wires. 

Step 6 

 

At the AC outlet, strip 

1

/

2

" of insulation from the ends of the low voltage wire. 

Attach these stripped ends to the transformer terminals. 

  

Make sure the exposed wires do not touch each other!

Step 7 

Plug the transformer into the electrical outlet. Use of a surge protector with the 

transformer is 

strongly

 recommended. If electrical outlet is 

located outdoors, outlet and transformer should be protected 

by a weatherproof cover.

 

 

First Gate Opener

Run 1000' (max.) of low

voltage wire to control

box from transformer

(wire not included).           

120 Volt indoor

Transformer

(surge protector 

not supplied)

PVC conduit (not included)

to protect wire from lawn

mowers and weed eaters.

Control and Battery Box

VAR5

VAR6

K1

PF1

K2

BATT 

+

BATT 

K3

K4

VAR4

VAR3

VAR2

VAR1

MIN

MAX OFF

JP1

REMOVE JUMPER FOR

PUSH TO OPEN OPTION

120

SEC.

G

TO Inc.   

Tallahassee, FL

R4722

STALL FORCE

OPEN  <  JOG  >  CLOSE

PWR.

SET

LIMIT

1st  OPR.

2nd  OPR.

STATUS

AUTO CLOSE

SFTY.

EXIT

CYCLE

EDGE

SENSOR

COMMON

LOCK+

LOCK–

WHT

GRN

RED

BLK

WHT

GRN

SECOND OPR

.

FIRST OPR

.

RED

BLK

14 VAC

OR   

SOLAR

ON  OFF

Low Voltage Wire from Solar

VAR6

BATT 

+

K3

K4

WHT

GRN

SECOND OPR

.

RED

BLK

14 VAC

OR   

SOLAR

ON  OFF

Low Voltage Wire

from Transformer

SURGE PROTECTOR

Transformer

Содержание E-Z GATE





































Отзывы: