GSW POWER VENTED GAS FIRED WATER HEATER Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 39

background image

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance
of injury, and tell you what can happen if the instructions are not followed.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING”.

DANGER

WARNING

You can be killed or seriously injured if you don’t immediately follow
instructions.

You can be killed or seriously injured if you don’t follow instructions.

INTRODUCTION

Thank you for purchasing a Flammable Vapour Ignition
Resistant Power Vented Water Heater.

This water heater is

designed to reduce the risk of

fl

ammable vapour related

fi

res

by shutting the burner down before

fl

ammable vapours get into

the water heater combustion chamber. This is achieved by the
means of the

fl

ammable vapour sensor. Properly installed and

maintained, it will provide years of trouble free service.
This gas-

fi

red water heater has been developed to produce

potable hot water for normal residential demands and may also
be used in combination with space heating applications.

User Responsibilities

This manual has been prepared to acquaint you with the
installation, operation and maintenance of your gas

fi

red

water heater and provide important safety information in these
areas. It is your responsibility to ensure that your water heater
is properly installed and cared for.

FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS
MANUAL MAY RESULT IN SERIOUS BODILY INJURY
AND/OR PROPERTY DAMAGE. THOROUGHLY READ
AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU
ATTEMPT TO INSTALL, OPERATE OR MAINTAIN THIS
HEATER.

Installation and service requires trade knowledge in the areas
of plumbing, electricity, venting, air supply and gas supply.
Only a quali

fi

ed service technician shall install or service this

water heater.

Service to the Power Vent System should only be performed
by a quali

fi

ed service technician.

The manufacturer of this water heater will not assume any
liability for any property damage, personal injury or death
resulting from improper sizing, installation or failure to comply
with these instructions.

Qualified Installer Or Service Agency

Installation and service of this water heater requires ability
equivalent to that of a Quali

fi

ed Agency in the

fi

eld involved.

Installation skills such as plumbing, air supply, venting,
gas supply and electrical supply are required in addition to
electrical testing skills when performing service.

Do not discard this manual. You or future users of this
water heater will need it for reference.

– 3 –

«
1
2
3
4
5
...
»

Содержание POWER VENTED GAS FIRED WATER HEATER








































Отзывы:

Нет отзывов

Похожие инструкции для POWER VENTED GAS FIRED WATER HEATER

Бренд: wallas Страницы: 40

Бренд: GEA Страницы: 337

Бренд: I.VA.CO. Страницы: 12

Бренд: Gardena Страницы: 17

Бренд: Gardena Страницы: 12

Instant-Flow Micro M-15L/277

Бренд: Chronomite Страницы: 2

Бренд: Little Giant Страницы: 8

Бренд: VITAE Страницы: 72

Бренд: Lasko Страницы: 4

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: pyromaster Страницы: 20

Бренд: A.O. Smith Страницы: 74

Бренд: Debem Страницы: 68

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

Type I CHILL-003

Бренд: BRAVILOR BONAMAT Страницы: 16

Бренд: Oasis Страницы: 20

Бренд: Biral Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды