background image

 LIMITED 

WARRANTY

LIMITED WARRANTY

RESIDENTIAL STORAGE TANK TYPE WATER HEATER FOR INSTALLATION IN A SINGLE FAMILY DWELLING

A.  WHO IS COVERED.

  GSW WATER HEATING AND ITS SUPPLIERS, (herein collectively referred to as “Manufacturer”) warrants only to the 

original consumer purchaser (hereinafter “Owner”) of the water heater, within the boundaries of the continental United 

States or Canada, or their territories, so long as he or she continuously occupies the single family dwelling in which this 

water heater is initially installed for the period speci

¿

 ed below. This Warranty is not transferable. This Warranty is reduced 

to one year if the water heater is used in a commercial or industrial application, or if the water heater is used to supply 

more than one dwelling unit. Consumers must retain point-of-sale proof of purchase to validate warranty entitlement.

B.  WHEN IT IS COVERED.

  The water heater is warranted only when it is installed, operated, and maintained in accordance with the printed instruc-

tions accompanying the water heater. The water heater shall/must be installed in such a manner that, if the tank or any 

connection thereto should leak, the resulting 

À

 ow of water will not cause damage to the area in which it is installed. The 

water heater’s temperature and pressure relief valve must be piped to the nearest drain to avoid damage in the event the 

valve is actuated. For detailed instructions, read the manual accompanying the water heater and review drawings in the 

manual.

C. WHAT THE MANUFACTURER WILL DO AND THE PERIOD OF COVERAGE.

 1. 

The Inner Tank

. If the inner tank leaks within the warranty period shown in the table above after the original installa-

tion, the Manufacturer will furnish a new water heater of the Manufacturer’s then prevailing comparable model. If in-

dustry standards, regulatory changes, product improvements, or product obsolescence prohibits the Manufacturer from 

furnishing an identical model replacement water heater under this Warranty, the Owner will be furnished with a new 

water heater of comparable capacity; however, the Owner will be charged for the additional value of the item(s) which 

the Manufacturer has incorporated in the replacement water heater. A prior authorization number must be obtained 

from the Manufacturer before replacing the water heater. This Warranty is limited to one replacement water heater at 

the original installation site.

 2. 

Component Part

. If any component, part other than the inner tank, proves to the Manufacturer’s satisfaction to be 

defective in material or workmanship within the warranty period shown in the table above after the original installation, 

the Manufacturer will furnish the Owner with a replacement for the defective part(s). This Warranty is limited to one 

replacement component part for each original part.

 3. 

Return of Defective Water Heater and Component Parts

. The Manufacturer reserves the right to examine the al-

leged defect in the water heater or component part(s). As such, it will be the Owner’s obligation (see paragraph D. 3) to 

return the water heater and/or component part(s) to the Manufacturer.

 

a.  When returning a water heater, it must include all component parts and the rating plate label.

 

b.  When returning component part(s), they must be individually tagged and identi

¿

 ed with the water heater’s Model 

Number, SKU, Serial Number, date of purchase, and date of installation.

 

c.  THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THIS 

EXPRESS WARRANTY IS, WHERE PERMITTED BY LAW, IN LIEU OF AND EXCLUDES AND REPLACES ALL 

OTHER CONDITIONS, WARRANTIES, GUARANTEES, REPRESENTATIONS, OBLIGATIONS OR LIABILITIES 

OF THE MANUFACTURER OF ANY NATURE OR KIND, EXPRESS OR IMPLIED, HOWEVER ARISING (WHETH-

ER BY CONTRACT, CONDUCT, STATEMENT, STATUTE, NEGLIGENCE, PRINCIPLES OF MANUFACTURER’S 

LIABILITY, OPERATION OF LAW, OR OTHERWISE) WITH RESPECT TO THE UNIT OR ITS FIRNESS FOR A 

PARTICULAR PURPOSE, METCHANTABILITY, INSTALLATION, OPERATION, REPAIR, OR REPLACEMENT. 

THE MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES. IN NO EVENT WILL 

THE MANUFACTURER’S LIABILITIES EXCEED THE COST OF THE DEFECTIVE PART(S) OR UNIT.

D. WHAT THIS WARRANTY DOES NOT COVER.

  1. The Unit must not be installed where water damage can result from a leak, while provision(s) shall be made for direct-

ing any water escaping from the Unit to a properly operating drainpipe. As all units of this type may eventually leak, 

you must protect against any potential water damage. The Manufacturer accepts no responsibility for such damage, 

nor any incidental or consequential loss, nor damage(s) related thereto, suffered by the Owner of the Unit nor by any 

third party.

  2. The Manufacturer shall not be liable under this Warranty and this Warranty shall be void and have no effect if the fol-

lowing events occur:

 

a.  The water heater or any of its component parts have been subject to misuse, alteration, neglect, or accident; or 

When referencing the water heater for service or warranty, please refer to the rating plate af

¿

 xed to the unit for the following 

information:

Use Copper Conductors Only

AUTOMATIC STORAGE WATER HEATER

For currenlly installed rating see element marking.
Caution: Pressure relief valve Iimiting the pressure 
to 1034 kPa (150 psI) musl be installed.
For safe operation, do not block pressure relief. 
This lank is equipped with a temperature limit 
device located under the upper access door.
CAUIlON: Risk of electrlc shock. Turn off power 
before opening access door. Do not turn on electric 
current until tank is full of water. Elements wlll bum 
out if tank is operated without water.

Pour seulement conducteurs copper

CHAUFFE-EAU A ACCUMIl.ATlON AUTOMATIQUE
La puissance installee est indiquee sur l'element.
ATTENTION: Une soupape de securite limitant la 
pression a 1034 kPa (150 psi) doit etre installee.
Pour un fonctionment securitaire, ne pas enlever 
ou bloquer cette soupape.
Ce reservoir est muni d'un dispositif reglage 
automatique de la temperature situe sous la porte 
d'acces superieure.
ATTENTION: Risque de choc electrique. Coupez le 
courant avant d'ouvrir la porte d'acces. Ne 
remettez pas le courant en marche avant que le 
reservoir soit remplis d'eau. Si le reservoir 
fonctionment sans eau, les elements bruleront.

Model Number

Catalogue Number
(SKU)

Serial Number

Rating Plate

Warranty Code:

P

R

S

U

V

W

Y

Inner Tank Warranty Years:

3

5

6

8

9

10

12

Component Part Warranty Years:

1

1

1

6

1

1

1

The Serial Number contains the warranty and manufacture date information for the unit as follows:

 

U9999 F999999 

Example: U1005 F001234

Warranty code 

Manufactured in week 5

Year of manufacture 

Manufactured in 2010

Week of manufacture 

8 year tank, 6 year parts warranty

The Warranty Code indicates the inner tank and component part warranties as shown in the table above.

 

– 38 – 

Содержание POWER VENTED GAS FIRED WATER HEATER








































Отзывы: