background image

 

GST-MNA2C/GST-MNA2F Network Annunciator                

                                              

Installation and Operation Manual

                 

                                                

 

 

Page 10  

 

Trouble  Information

:  If flashes when  a  fault message  is  not  confirmed.  It  goes 

steady  when  all  fault  messages  have  been  confirmed;  it  goes  out  as  all  fault 

messages are cleared.  

 

Disable Information

: It lights when a disabled message exists; it goes out when all 

disabled conditions are cleared.   

 

Status Information

: It lights when any message exists; it goes out as all messages 

are cleared. 

 

NAC

: It lights when there is notification appliance circuit (NAC) activated. It goes 

out when there is any notification appliance circuit (NAC) 

silenced.

 

4.2 Functional Keys 

 

Fire Alarm Information

: Fire alarm information screen is displayed when there is 

fire alarm information and this key is pressed.  

 

Supervisory Information:

 Supervisory signal may be programmed as latching or 

non-latching. For latching supervisory, cancellation of the signal is the indication of 

restoration  to  normal  condition.  For  non-latching  supervisory,  the  signal  will  be 

locked-in until manually reset.  Supervisory information screen is displayed when 

there is supervisory information and this key is pressed.  

 

Trouble  Information

:  Fault  information  screen  is  displayed  when  there  is  fault 

information as this key is pressed.  

 

Disable  Information

:  Disable  information  screen  is  displayed  when  there  is 

disable information as this key is pressed. 

 

Status  Information

: Status information screen is displayed when there is status 

information as this key is pressed. 

 

Manual Alarm

: Pressing the key shall activate alarm process, referred to section 

6.1.4 

 

Acknowledge

: Pressing the key will acknowledge the selected message.                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                              

 

Silence Alarm

: All activated NACs can be silenced when this key is pressed. 

 

Silence Buzzer

: Buzzer can be silenced when this key is pressed.  

 

All Resound

: All deactivated NACs can be resound when this key is pressed.  

 

RESET

: The system will be reset as this key is pressed.  

4.3 Service / Program Keys: 

 

 

 

Key 

Description 

Number Key 

of 0~9 

Press number keys to input numbers. 

Содержание GST-MNA2C































Отзывы: