GSi Autoflow 2000 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 55

GSi Autoflow 2000 Series Скачать руководство пользователя страница 40

2000 Autoflow

40

ELECTRICAL POWER SUPPLY

Autoflow to Master Fan/Heater Unit Interconnect

The Master Fan/Heater Unit is the only fan and
heater in a single fan unit. In two fan units it is the
fan/heater with the airswitch, plenum temperature
sensor, and grain temperature sensor connected to
it. DO NOT run the control wires for the Master
Fan/Heater in the same conduit as the power wires
for the fan motor. To wire the Master Fan/Heater
Unit to the Autoflow Control Box do the following.

Important!

NOTE: Do NOT use solid wire for

interconnections.

NOTE: A shielded 16 gauge cable is recommended
for use on the network connection. The network
wires for this configuration are attached to terminals
number 4 and 5. Ground each end of the shielded
cable to the housing. A shielded 16 gauge 2 wire
cable can be purchased from GSI. Part # WR-16
/ 2S.

1)

Run five (5) control wires from the
Autoflow Control Box to the Master
Fan/Heater Unit.

2)

Connect the wires as shown in figure 19.

Figure 19

Master Fan and Heater Dipswitch Setting : #1 - “Off” / All Others - “On”

«
...
38
39
40
41
42
...
»

Содержание Autoflow 2000 Series
























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды