Groen HY-3E Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 38

background image

OM/SM-HY-3E & HY-5E(CE)

35

9.

Hold door spring open with a screwdriver or
similar tool, hold door handle in the DOWN
position and install the U-channel, top end
first - then lower channel into position. Check
that spring opens when door handle is
pushed up.

10. Apply Locktite 242 to U-channel mounting

screws, then install the screws.

X. Door Locking Pin Pin

Lock Nut

P/N 078914

P/N 003823

1.

Turn off steamer and allow it to cool.

2.

Note and record the distance between the
lock nut and the end of the (bullet shaped)
door locking pin. This information is
important and will be needed for installation.

3.

Loosen lock nut and remove lock nut and
door pin (bullet) from front panel.

4.

To install new door locking pin, coat locking
pin threads with a few drops of Locktite 222.

5.

Install locking pin and lock nut. The lock nut
to end-of-bullet distance should be
approximately the same as measured
above, in Step 2.

Y. Alternate Door Switch Location

The alternate door switch is located on the left side
of the steamer as viewed from the front. In order to
gain access to the switch for replacement purposes
only, it is required to remove the right panel and
top/left cover.

The leads for this alternate switch are provided
adjacent to the wiring harness on the right side of the
steamer. Refer to Section B and S for more
instructions.

https://appliancetechmanuals.com

«
...
33
34
35
36
37
...
»

Содержание HY-3E







































Отзывы:

Нет отзывов

Похожие инструкции для HY-3E

Бренд: Qingdao H.Y Страницы: 6

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: Gastrodomus Страницы: 39

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды