Grizzly T1244 Скачать руководство пользователя страница 9

Страница: 9 / 32

Model T1244 (Mfd. Since 10/17)

-7-

SECTION 2: SETUP

This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.

If items are damaged,

please call us immediately at (570) 546-9663.

IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-
aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.

Unpacking

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine. Discard immediately.

The following items are needed, but not included,
for the setup/assembly of this machine.

Description Qty
•

Another Person .......................................... 1

•

Safety Glasses ................. 1 Pair per Person

•

Cleaner/Degreaser (

Page 10) .... As Needed

•

Disposable Shop Rags ............... As Needed

•

Straightedge 24" ......................................... 1

•

Phillips Screwdriver #2 ............................... 1

•

Open-End Wrench 10mm ........................... 1

•

Open-End Wrench 13mm ........................... 1

•

Open-End Wrench 17mm ........................... 1

•

Additional Wrenches .................. As Needed

•

Grade 5 Fasteners ..................... As Needed

•

Masking Tape ............................. As Needed

•

Razor Blade ................................................ 1

•

Dust-Collection System .............................. 1

•

Dust Hose 2

⁄

" ........................................... 1

•

Hose Clamps 2

⁄

" ...................................... 2

•

Table Saw Owner's Manual ........................ 1

•

Router Owner's Manual .............................. 1

•

Tape or Erasable Marker ............................ 1

•

Center Punch ............................................. 1

•

Drill ............................................................. 1

•

Drill Bits ...................................... As Needed

•

Countersink Bit ........................................... 1

•

Fasteners .................................... As Needed

Needed for Setup

This item presents serious

injury hazards to untrained

users. Read through this

entire manual to become

familiar with the controls

and operations before

using this item!

Wear safety glasses during

the entire setup process!

This item and its compo-

nents are very heavy. Get

lifting help to move heavy

items.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine

with respect and caution to reduce risk of

operator injury. If normal safety precautions

are overlooked or ignored, serious personal

injury may occur.

Содержание T1244

































Результаты поиска

Содержание T1244

Отзывы:

Похожие инструкции для T1244

Бренды по названию

Популярные бренды

Grizzly T1244, Руководство пользователя

Результаты поиска

Содержание T1244

Отзывы:

Похожие инструкции для T1244

Бренды по названию

Популярные бренды