manualshive.com logo in svg

Grizzly Polar Bear G0833P, Руководство пользователя, Страница: 9 / 92

Поделиться
Скачать
Grizzly Polar Bear G0833P Скачать руководство пользователя страница 9

Model G0833P (Mfd. Since 06/17)

-7-

The information contained herein is deemed accurate as of 9/17/2017 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

PAGE 2 OF 3

Model G0833P

Motors:

Main

Horsepower................................................................................................................................................ 2 HP

Phase............................................................................................................................................ Single-Phase

Amps....................................................................................................................................................... 16A/8A

Speed................................................................................................................................................ 3450 RPM

Type................................................................................................................. TEFC Capacitor-Start Induction

Power Transfer ....................................................................................................................... Poly-V Belt Drive

Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications:

Main Information

Table Saw Type....................................................................................................................................... Hybrid

Maximum Blade Diameter......................................................................................................................... 10 in.

Arbor Size................................................................................................................................................. 5/8 in.

Arbor Speed...................................................................................................................................... 3850 RPM

Maximum Width of Dado...................................................................................................................... 13/16 in.

Blade Tilt Direction....................................................................................................................................... Left

Max Blade Tilt......................................................................................................................................... 45 deg.

Maximum Depth of Cut At 90 Degrees.................................................................................................. 3-1/8 in.

Maximum Depth of Cut At 45 Degrees................................................................................................ 2-3/16 in.

Max Rip Right of Blade w/Included Fence & Rails.............................................................................. 31-1/2 in.

Max Rip Left of Blade w/Included Fence & Rails................................................................................. 11-3/8 in.

Additional Blade Information

Included Blade Information.................................................................................................................. 10" x 40T

Riving Knife/Spreader Thickness.............................................................................................................. 0.1 in.

Required Blade Body Thickness.............................................................................................. 0.063 – 0.094 in.

Required Blade Kerf Thickness............................................................................................... 0.102 – 0.126 in.

Rim Speed at Max Blade Diameter................................................................................................. 10,074 FPM

Table Information

Floor to Table Height........................................................................................................................... 34-1/4 in.

Table Size with Extension Wings Width.................................................................................................... 40 in.

Table Size with Extension Wings Depth.................................................................................................... 27 in.

Distance Front of Table to Center of Blade......................................................................................... 16-1/4 in.

Distance Front of Table to Blade At Maximum Cut............................................................................. 11-1/2 in.

Main Table Size Thickness.................................................................................................................... 1-1/2 in.

Fence Information

Fence Type.................................................................................... Camlock T-Shape w/High-Low Profile Face

Fence Size Length............................................................................................................................... 34-5/8 in.

Fence Size Width.................................................................................................................................. 4-5/8 in.

Fence Size Height....................................................................................................................................... 3 in.

Fence Rail Type............................................................................................... Square Steel Tubing/Angle Iron

Fence Rail Length............................................................................................................................... 61-7/8 in.

Fence Rail Width......................................................................................................................................... 2 in.

Fence Rail Height.................................................................................................................................. 1-5/8 in.

Miter Gauge Information

Miter Gauge Slot Type.............................................................................................................................. T-Slot

Miter Gauge Slot Size Width..................................................................................................................... 3/4 in.

Miter Gauge Slot Size Height................................................................................................................... 3/8 in.

Содержание Polar Bear G0833P





























































































Отзывы:

Нет отзывов