manualshive.com logo in svg

Grizzly Polar Bear G0833P, Руководство пользователя, Страница: 63 / 92

Поделиться
Скачать
Grizzly Polar Bear G0833P Скачать руководство пользователя страница 63

Model G0833P (Mfd. Since 06/17)

-61-

Troubleshooting

Symptom

Possible Cause

Possible Solution

Machine  does  not 
start,  or  power 
supply 

breaker 

immediately  trips 
after startup.

1.  Locking pin installed in switch.
2.  Machine circuit breaker tripped.
3.  Power supply circuit breaker tripped or fuse 

blown.

4.  Plug/receptacle at fault/wired incorrectly.
5.  Motor wires connected incorrectly.
6.  Wiring open/has high resistance.
7.  START/STOP  switch  or  circuit  breaker  at 

fault.

8.  Start capacitor at fault.
9.  Motor at fault.

1.  Remove locking pin from START button.
2.  Reset circuit breaker on switch.
3.  Ensure  circuit  is  sized  correctly  and  free  of  shorts. 

Reset circuit breaker or replace fuse.

4.  Test for good contacts; correct the wiring.
5.  Correct motor wiring connections (

Page 76).

6.  Check/fix broken, disconnected, or corroded wires. 
7.  Replace switch/circuit breaker.

8.  Test/replace if faulty.
9.  Test/repair/replace.

Machine  stalls  or  is 
underpowered.

1.  Feed rate/cutting speed too fast.
2.  Workpiece material unsuitable for machine.
3.  Motor  overheated;  tripping  machine  circuit 

breaker.

4.  Blade dull or incorrect for type of cut.
5.  Belt(s) slipping.
6.  Motor wired incorrectly.
7.  Pulleys slipping on shaft or misaligned.

8.  Run capacitor at fault.
9.  Motor bearings at fault.
10. Contactor not energized/has poor contacts.
11. Centrifugal switch at fault.
12. Motor at fault.

1.  Decrease feed rate/cutting speed.
2.  Only cut wood/ensure moisture is below 20%.
3.  Clean  motor/let  cool,  and  reduce  workload.  Reset 

breaker.

4.  Use correct, sharp blade; reduce feed rate.
5.  Tension/replace belt(s).
6.  Wire motor correctly (

Page 76).

7.  Tighten/replace  loose  pulley;  ensure  pulleys  are 

aligned (

Page 74)

8.  Test/repair/replace.
9.  Test/repair/replace.
10. Test all legs for power/replace if faulty.
11. Adjust/replace centrifugal switch if available.
12. Test/repair/replace.

Machine has 
vibration or noisy 
operation.

1.  Motor or component loose.

2.  Blade at fault.
3.  Belt(s)/pulley(s) worn, loose, or misaligned.

4.  Motor mount loose/broken.
5.  Machine  incorrectly  mounted/resting  on 

floor.

6.  Arbor pulley loose.
7.  Motor fan rubbing on fan cover.
8.  Arbor bearings at fault.
9.  Motor bearings at fault.

1.  Inspect/replace  damaged  bolts/nuts,  and  re-tighten 

with thread-locking fluid.

2.  Replace warped/bent blade; resharpen dull blade.
3.  Inspect/replace belts with new matched set. Realign/

replace shaft, pulley, set screw, and key (

Page 74).

4.  Tighten/replace.
5.  Tighten mounting bolts; relocate/shim machine.

6.  Retighten/replace arbor pulley.
7.  Fix/replace fan cover; replace loose/damaged fan.
8.  Replace arbor housing bearings; replace arbor. 
9.  Test by rotating shaft; grinding/loose shaft requires 

bearing replacement.

Review  the  troubleshooting  and  procedures  in  this  section  if  a  problem  develops  with  your  machine.  If 
you need replacement parts or additional help with a procedure, call our Technical Support. 

Note: Please 

gather the serial number and manufacture date of your machine before calling.

SECTION 8: SERVICE

Содержание Polar Bear G0833P





























































































Отзывы:

Нет отзывов