Grizzly Polar Bear G0833P Скачать руководство пользователя страница 88

Страница: 88 / 92

-86-

Model G0833P (Mfd. Since 06/17)

Labels & Cosmetics

G0833P Machine Labels A

(06/19/17)

• 1:1 Scale (Labels are

actual size)

• Labels must be made of

chemical-resistant material

Specifications

WARNING!

Motor: 2 HP, 115V/230V, 60 Hz, Single-Phase

Pre-Wired: 230V

Full-Load Current Rating: 16A at 115V, 8A at 230V

Blade Size: 10" x 5/8" Arbor

Required Blade Kerf Thickness: 0.102"–0.126"

Arbor Speed: 3850 RPM

Max. Rip Capacity: 31-1/2"

Max. Depth of Cut @ 90˚: 3-1/4"

Max. Depth of Cut @ 45˚: 2-1/4"

Max. Dado Width: 13/16"

Weight: 396 lbs.

Date

Mfd. for Grizzly in China

MODEL G0833P

POLAR BEAR SERIES

™

10" HYBRID TABLE SAW

12.  Make sure blade is stopped before adjusting the height or tilt.
13.  Do not perform any operation freehand.
14.  Never use fence and miter gauge at the same time.
15.  Ensure machine is stable and fence is parallel with blade.
16.  Disconnect power before changing blades or servicing saw.
17.  Plan cuts so that workpieces always remain supported.
18.  Non-through cuts (i.e. dadoes, rabbets, moulding cuts) and
    resawing cuts present specific dangers; refer to the manual.
19.  Do not wear loose clothing, gloves, jewelry, or other items that
    can get entangled. Tie back long hair and roll up sleeves.
20.  Do not expose to rain or operate in a wet environment.
21.  Prevent unauthorized use by children or untrained users;
    restrict access or disable machine when unattended.

To reduce risk of serious injury when using this machine:

  1. Read and understand owner’s manual before operating.
  2.  Never touch moving blade, and keep hands out of cutting path.
  3. Always wear approved eye protection and respirator.
  4.  Only plug power cord into a grounded outlet.
  5.  Always use blade guard/spreader for all through cuts; and use
    riving knife for all non-through cuts. If a certain cut cannot be
    made with either device, some other safeguard MUST be used.
  6.  Only use blades meeting size/speed requirements for this saw.
  7.  Ensure spreader/riving knife and fence are properly adjusted.
  8.  Never reach behind or over blade while it is moving.
  9.  Use a push stick when required and whenever possible,
    especially with small/narrow workpieces and non-through cuts.
10.  Know what causes “kickback” and how to prevent it.
11.  Never remove jammed/cutoff workpiece when blade is moving!

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

COLOR CODES

GRIZZLY LOGO RED

PANTONE 711C or RAL 3020

GRIZZLY GREEN

PANTONE 568C

GRIZZLY LOGO YELLOW

PANTONE 7406C or RAL 1003

PANTONE 151 C or RAL 2005

WARNING

***

G0833P Machine Labels C

(06/13/17)

• Scale= 1:1

(unless otherwise noted)

• Labels MUST be made of

chemical-resistant material

***These labels must have individual

letters/numbers.

Do not print with clear background.

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL!

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at

[email protected]

G0833P

***

COLOR CODE

GRIZZLY GREEN

PANTONE 568C

RAL 9010

GRIZZLY GRAY

FOR GRIZZLY MACHINES ONLY! All labels created by Grizzly Industrial, Inc. are

copyrighted and must only be used on Grizzly brand machines. Never use Grizzly’s label

artwork on other brands of machines.

Scale 1:1

grizzly.com

USE PANTONE DS 9-9C

Use G8588

G0715P Machine Labels 2

(06/26/15)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

INJURY HAZARD

Keep door closed

while blade is in

motion. Disconnect

power before

opening door.

WARNING!

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0715P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible

with riving knife.
• Max Width 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com

WARNING!

DANGER

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

WARNING

CAUTION

PANTONE 109 C

NOTICE

PANTONE 3005 C or RAL 5005

Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!

G0833P Machine Labels B

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

stopping positions with excessive force could

G0833P Machine Labels B

(06/13/17)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

G0833P Machine Labels B

(06/13/17)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

G0833P Machine Labels B

(06/13/17)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

G0833P Machine Labels B

(06/13/17)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

G0833P Machine Labels B

(06/13/17)

• Scale= 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

chemical-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

Disconnect power
before changing
blades or blade
guard and riving
knife.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.

If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.

AMPUTATION

HAZARD!

Always keep
fingers and
hands away from
moving blade.

Disconnect power
before changing
blades or blade
guard and riving
knife.

The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:

BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with

spreader or riving knife.

Dado Blades
• Dado blades under 10"

diameter not compatible
with riving knife.
• Max Width: 13/16"

DANGER

WARNING

CAUTION

NOTICE

PANTONE 3005 C or RAL 5005

PANTONE 485 C or RAL 3001

COLOR CODES

PANTONE 151 C or RAL 2005

PANTONE 109 C

service.

G0833P Machine Labels

(06/19/17)

Debris on front rail

can misalign fence

and increase risk of

kickback.

Reduce this risk by

cleaning front rail

before positioning

fence.

Industrial Rip Fence

(Actual Size)

Debris on front rail

can misalign fence

and increase risk of

kickback.

Reduce this risk by

cleaning front rail

before positioning

fence.

G0833P Fence

(Shown at 40% Actual Size)

Back

Front

701

702

703

704

705

706

707

708

709

710

711

712

713

714

715

716

717

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

701 P0833P701 MACHINE ID LABEL

710 P0833P710 TOUCH-UP PAINT, POLAR BEAR WHITE

702 P0833P702 READ MANUAL LABEL

711 P0833P711 EYE/LUNG HAZARD LABEL

703 P0833P703 TABLE SAW WARNING LABEL

712 P0833P712 GRIZZLY NAMEPLATE G8588

704 P0833P704 RIVING KNIFE CAUTION LABEL

713 P0833P713 TOUCH-UP PAINT, GRIZZLY GREEN

705 P0833P705 DISCONNECT POWER LABEL

714 P0833P714 POLAR BEAR LOGO LABEL

706 P0833P706 ELECTRICITY LABEL

715 P0833P715 MODEL NUMBER LABEL

707 P0833P707 DON'T OPEN DOOR WARNING LABEL

716 P0833P716 GRIZZLY.COM LABEL

708 P0833P708 BLADE GUARD LABEL

717 P0833P717 FENCE LABEL

709 P0833P709 HANDWHEELS NOTICE LABEL

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

Содержание Polar Bear G0833P





























































































Результаты поиска

Содержание Polar Bear G0833P

Отзывы:

Grizzly Polar Bear G0833P, Руководство пользователя, Страница: 88 / 92

Результаты поиска

Содержание Polar Bear G0833P

Отзывы: