Grizzly G0894 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

background image

-28-

Model G0894 (Mfd. Since 05/19)

Homing Axes

Homing  the  machine  returns  all  three  axes  to
"home"  position  or  the  machine-specific  zero
point.  Home  is  determined  by  magnetic  limit
switches  and  will  not  change.  Since  all  machine
movement is calculated from home, always home
axes and verify machine parameters before each
operation.

To home axes:

1. Press HOME. Verify all axes move to their

farthest positions.

2. Verify all machine parameters listed in

Verifying Parameters on Page 22.

Setting Work Origin

Work origin is the workpiece-specific zero point,
the starting point for your toolpath. All three axes
need to be zeroed at the work origin before run-
ning code.

The Z-axis can be set in relation to either the table
surface or the workpiece surface, but it must cor-
respond to what is established in the G-code. If
this is not done properly, the cutter may crash into
the material or the table, causing damage to the
workpiece or the machine.

To set work origin:

1. Clamp workpiece to table, insert cutter, and

load G-code onto controller.

2. Manually move X- and Y-axes to toolpath

origin established in G-code.

3. Manually move Z-axis down to

1

⁄

8

" above

workpiece or table surface (as determined by
G-code).

4. Place piece of paper between cutter tip and

surface. Slowly step Z-axis down while slid-
ing paper until paper cannot move.

5. Press XY->0 to set X- and Y-axis origin.

6. Press Z->0 to set Z-axis origin.

Set work origin before each unique opera-

tion. The work origin of all axes must match

the origin of the toolpath established in the

G-code. Failure to set the work origin may

cause the cutter to crash and damage the

workpiece, machine, or cutter.

1. Press MODE to toggle between Continuous,

Step, and Distance modes.

— In Continuous mode, press and hold axis

movement buttons to move axes. Release
button to stop movement.

— In Step mode, press button to move axis

one step. Step size is determined by
speed mode.

— In Distance mode, press button to move

axis  a  user-defined  distance.  Controller
will  display  current  setting  while  in  dis-
tance  mode.  Press  RUN/PAUSE  to  edit
distance, then OK to save.

Changing Axis Movement Mode

«
...
28
29
30
31
32
...
»

Содержание G0894

















































Отзывы:

Нет отзывов

Похожие инструкции для G0894

Бренд: Chicago Pneumatic Страницы: 32

Бренд: PowerBox Systems Страницы: 30

Router Table Spline Jig

Бренд: Rockler Страницы: 8

Бренд: Parkside Страницы: 27

Бренд: FESTA Страницы: 42

Бренд: Neilsen Страницы: 2

Бренд: Matco Tools Страницы: 10

Бренд: Westfalia Страницы: 46

Бренд: SATA Страницы: 28

Бренд: REMAN Tools Страницы: 23

Бренд: EINHELL Страницы: 38

Бренд: Widearea Страницы: 9

Бренд: Facom Страницы: 272

Бренд: Workshop Страницы: 3

Бренд: Wen Страницы: 24

Бренд: Extron electronics Страницы: 1

Бренд: Makita Страницы: 76

Бренд: Clayton Power Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды