GREISINGER ResOx 5695 Скачать руководство пользователя страница 4

H84.0.15.6C-01 

Operating manual ResOx 5695 

Page 4 of 22 

 

 

_____________________________________________________ 

_____________________________________________________________________________ 

 

1.5  Reasonably foreseeable misuse 

 

This device 

must not be used

 at potentially explosive areas! 

Do not use these products as safety or emergency stop devices or in any other application 
where failure of the product could result in personal injury or material damage. 
Failure to comply with these instructions could result in death or serious injury and 
material damage. 

 

This device must not be used at a patient for diagnostic or other medical purpose. 

1.6  Safety guidelines 

This device has been designed and tested in accordance with the safety regulations for electronic devices. 
However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures 
and special safety advises given in this manual will be adhered to when using the device. 

 

Trouble-free operation and reliability of the device can only be guaranteed if the device is 
not subjected to any other climatic conditions than those stated under 20 Specification. 

 

If there is a risk whatsoever involved in running it, the device has to be switched off 
immediately and to be marked accordingly to avoid re-starting. 
Operator safety may be a risk if: 
- there is visible damage to the device 
- the device is not working as specified 
- the device has been stored under unsuitable conditions for a longer time. 
In case of doubt, please return device to manufacturer for repair or maintenance. 

 

Internal connections of other devices (e.g. from ground with protective earth) may lead to 
prohibited voltage levels that could disturb the function, damage or even destruct the 
device or any connected equipment. 

Product description 

2.1  Scope of supply 

The scope of supply includes: 

  Handheld instrument ResOx 5695 with 2 AAA-Batteries 

(oxygen sensor usually is ordered separately. For choice please refer to chapter 6 The oxygen 
sensor) 

  Operating manual 

  Short form manual 

  Calibration protocol 

  Silicone protective cover 

 

 

Содержание ResOx 5695























Отзывы: