background image

EK628 Battery-powered Crimping Tool

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY 

ALERT 

SYMBOL

This symbol is used to call your attention to 

hazards or unsafe practices which could result in 

an injury or property damage. The signal word, 

defined below, indicates the severity of the hazard. 

The message after the signal word provides infor-

mation for preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL 

result in severe injury or death.

Hazards which, if not avoided, COULD result in 

severe injury or death.

Hazards or unsafe practices which, if not avoided, 

MAY result in injury or property damage.

Read and understand all of the 

instructions and safety information  

in this manual before operating or 

servicing this tool.
Failure to observe this warning 

could result in severe injury or 

death.

Electric shock hazard:
This tool is not insulated. When 

using this unit near energized 

electrical lines, use proper personal 

protective equipment.
Failure to observe this warning 

could result in severe injury or 

death.

Wear eye protection when operat-

ing or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from 

flying debris or hydraulic oil. 

Skin injection hazard:
Do not use hands to check for 

oil leaks. High pressure oil easily 

punctures skin causing serious 

injury, gangrene, or death. If injured, 

seek medical help immediately to 

remove oil.

Do not use solvents or flammable 

liquids to clean the crimping tool. 

Solvents or flammable liquids could 

ignite and cause serious injury or 

property damage.

An incomplete crimp can cause a fire.

Use proper die, connector, and cable combina-

tions. Improper combinations can result in an 

incomplete crimp.
The relief valve will sound to indicate a completed 

crimp, and the ram will retract. If you do not hear 

the sound of the relief valve, the crimp is not 

 complete.

Failure to observe these warnings could result in 

severe injury or death.

Keep hands away from the crimp-

ing head when crimping.
Failure to observe this warning 

could result in severe injury or 

death.

Содержание GATOR EK628













Отзывы: