background image

all products manufactured by Cooper Controls and identified with the Greengate brand are warranted to be free from defects in material and workmanship and 

shall conform to and perform in accordance with seller’s written specifications for a period of :

Five (5) years from date of shipment for all occupancy sensors. 

• 

three (3) years from date of factory invoice for our hardware and software on lighting Control Panels.

• 

We warranty all our standard relays for a period of 10 years from date of factory invoice.  We guarantee the performance of our system to specifications of your 

• 

money back.

this warranty will be limited to the repair or replacement, at seller’s discretion, of any such goods found to be defective, upon their authorized return to seller. this 

limited warranty does not apply if the goods have been damaged by accident, abuse, misuse, modification or misapplication, by damage during shipment or by 

improper service. there are no warranties, which extend beyond the hereinabove-limited warranty, InClUDInG, BUt not lIMIteD to, the IMPlIeD WaRRantY 

oF MeRChantaBIlItY anD the IMPlIeD WaRRantY oF FItness. 
no employee, agent, dealer, or other person is authorized to give any warranties on behalf of the seller or to assume for the seller any other liability in connection 

with any of its goods except in writing and signed by the seller. 
the seller makes no representation that the goods comply with any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s re-

sponsibility. the use of the seller’s goods should be in accordance with the provision of the national electrical Code, Ul and/or other industry or military standards 

that are pertinent to the particular end use. Installation or use not in accordance with these codes and standards could be hazardous.

P/N 05-0206XX-04

Cooper Controls

203 Cooper Circle, Peachtree, Ga 30269

800-553-3879

www.coopercontrol.com 

Содержание ControlKeeper 2 CK2-120-NC








Отзывы: