Gree U-Match GU100T/A1-K Скачать руководство пользователя страница 46

Страница: 46 / 54

U-Match Series Cassette Type Unit

GU125W/A1-M, GU140W/A1-M, GU160W/A1-M:

3.4 Check after Installation

Check Items after Installation

Check items

Possible events due to improper

insta

lation.

Is the main body installed securely?

The unit may fall down, vibrate or
produce noise.

Did you do water leakage test?

Cooling capacity may become
unsatisfactory.

Is the unit well insulated from heat?

Condensate, water drops may occur.

Does water drainage go well?

Condensate, water drops may occur.

Is the voltage consistent with that stated
on the nameplate?

The unit may fail or its components
may get burned.

Are the wires and pipes installed
correctly?

The unit may fail or its components
may get burned.

Has the unit been safely grounded?

Risk of electric leakage.

Do the specifications of wires comply with
the requirement?

The unit may fail or its components
may get burned.

Is there any obstacle blocking the air inlet
and outlet of the indoor or outdoor units?

Cooling capacity may become
unsatisfactory.

Have you recorded the length of
refrigerant pipe and the refrigerant
charging amount?

The refrigerant charging amount can’t
be controlled.

3.5 Test Running

Preparation before connecting the power

(1) Power must not be connected if the installation work is not completed.

Содержание U-Match GU100T/A1-K























































Результаты поиска

Содержание U-Match GU100T/A1-K

Отзывы:

Бренды по названию

Популярные бренды

Gree U-Match GU100T/A1-K, Руководство пользователя

Результаты поиска

Содержание U-Match GU100T/A1-K

Отзывы:

Бренды по названию

Популярные бренды