Gree U-Match GU100T/A1-K Скачать руководство пользователя | Manualshive

Страница: 44 / 54

background image

U-Match Series Cassette Type Unit

40

WARNING!

③

.

High and low voltage wires should be secured separately. Secure the former
ones with big clamps and the latter ones with small clamps.

④

.

Use screws to tighten up the connection wires and power cords of indoor and
outdoor units on the terminal board. Wrong connection may lead to fire hazard.

⑤

.

If the connection wires of indoor unit (outdoor unit) and power cords are not
correctly connected, the air conditioner may get damaged.

⑥

.

Ground the indoor and outdoor units through connecting the ground wire.

⑦

.

The units should comply with applicable local and national rules and regulations
on power consumption.

⑧

.

When connecting the power cord, make sure the phase sequence of the power
supply matches with the corresponding terminals, otherwise the compressor will
get reversed and operate abnormally.

1) Indoor side

Take off the electric box cover from the sub-assembly of electric box. Then

connect the wires. Connect the connection wires of indoor unit according to the
corresponding marks.

«
...
42
43
44
45
46
...
»

Содержание U-Match GU100T/A1-K























































Отзывы:

Нет отзывов

Похожие инструкции для U-Match GU100T/A1-K

Бренд: Valeo Страницы: 15

PREFERRED 124ANS

Бренд: Bryant Страницы: 6

AirConServiceCenter ASC 2500 G LE

Бренд: Waeco Страницы: 356

Бренд: Dimplex Страницы: 15

Бренд: Trane Страницы: 28

T?CLASS TPA024S4

Бренд: Lennox Страницы: 32

BAYECON353 Series

Бренд: Trane Страницы: 24

OTEC ICHD009J0A-DMG026

Бренд: Omega Страницы: 67

Бренд: Bestron Страницы: 52

Бренд: Daitsu Страницы: 56

bycool SPLIT OFF ROAD

Бренд: dirna Bergstrom Страницы: 56

Suburban Dynaline 3 DYNA07AC

Бренд: ACS Страницы: 38

Бренд: HAMILTON BEACH/PROCTOR SILEX Страницы: 14

Бренд: Panasonic Страницы: 95

Бренд: Panasonic Страницы: 117

Бренд: Panasonic Страницы: 127

Бренд: Panasonic Страницы: 85

Бренд: Haier Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды