background image

U-Match Series Cassette Type Unit 

26 

3.2.5 Refrigerant Adding 

See the following table for the amount of additional refrigerant. 

Item 

Standard 

Pipe Length   

Unnecessary Charge 

Pipe Length   

Additional Refrigerant 

Amount for Extra Pipe 

GU50W/A1-K 

5.0m 

≤7.0m 

22 g/m 

GU71W/A1-K 

5.0m 

≤7.0m 

30 g/m 

GU85W/A1-K 

5.0m 

≤7.0m 

30 g/m 

GU100W/A1-M 

5.0m 

≤7.0m 

45 g/m 

GU125W/A1-M 

5.0m 

≤7.0m 

45 g/m 

GU140W/A1-M 

7.5m 

≤9.5m 

45 g/m 

GU160W/A1-M 

7.5m 

≤9.5m 

54 g/m 

3.2.6 Installation of Drain Hose 

(1)  It is not allowed to connect the condensate drain pipe into waste pipe or 

other pipelines which are likely to produce corrosive or peculiar smell to 
prevent the smell from entering indoors or corrupt the unit. 

(2)  It is not allowed to connect the condensate drain pipe into rain pipe to 

prevent rain water from pouring in and cause property loss or personal 
injury. 

(3)  Condensate drain pipe should be connected into special drain system for 

air conditioner. 

3.2.6.1 Indoor Side Drainage Pipe 

(1)  Keep pipe size equal to or greater than that of the connecting pipe. 
(2)  Install the drain piping as shown and take measures against 

condensation.     

 

(3)  Keep piping as short as possible and slope it downwards at a gradient of 

at least 1/100 so that air may not remain trapped inside the pipe. 

(4)  If the drain pipe can’t be installed at a proper inclination, then add drain lift 

pipe.   

Содержание U-Match GU100T/A1-K























































Отзывы: