background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability
exceed the original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without
notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION.

IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING
THE ASSEMBLY AND USE OF THIS MODEL.

USB4P03 for GPMA0390  V:1.0  Printed in USA

Entire Contents © Copyright 2002

1610 Interstate Drive Champaign, IL 61822

(217) 398-8970, Ext. 2

[email protected]

INSTRUCTION MANUAL

Wingspan: 58-1/2 in [1485mm] 
Wing Area: 595 sq in [38.4 dm

2

Weight: 5.3-5.7 lbs [2400 – 2600g] 
Wing Loading: 20.5-22.3 oz/sq ft [62.5 – 67.7 g/dm

2

]

Length: 46 in [1170mm] 
Radio: 4-Channel with 5 servos
Engine: .40 to .52 cu in [6.5 – 8.5cc] two-stroke, .52 to

.70 cu in [8.5 – 11.5cc] four-stroke

Содержание Ultra Sport 40 Plus































































Отзывы: