background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This

warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability exceed the original cost of
the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for any
damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user accepts all
resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately
in new and unused condition to the place of purchase.

To make a warranty claim, send the defective part or item to Hobby Services at this address.

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822

USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax number, e-mail
address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package the problem will be evaluated as
quickly as possible.

READ THIS MANUAL BEFORE STARTING
CONSTRUCTION.

IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING
THE ASSEMBLY AND USE OF THIS MODEL.

GPMZ0198 for GPMA1349  V1.0

Entire Contents © Copyright 2005

Champaign, IL

(217) 398-8970, Ext. 5

[email protected]

INSTRUCTION MANUAL

Wingspan: Top Wing: 71.5 in [1815mm]

Bottom Wing: 69 in [1755mm]

Wing Area: Top WIng: 762 sq in [49.1 dm

2

Bottom Wing: 704 sq in [45.4 dm

2

]

Weight: 14.5 – 15.5 lb [6580 – 7030 g]
Wing Loading: 23 – 24 oz/sq ft [69-74 g/dm

2

Length: 57 in [1450mm] 
Radio: 4-channel with 5 servos
Engine:

.91-1.08 cu in [15-17.5cc] two-stroke,
.91-1.20 cu in [19.5-23cc] four-stroke

Содержание PT-17 Stearman





































Отзывы: