background image

20

Flying

Once the FlyLite is in the air think 

gentle

. Remember, the FlyLite is primarily an indoor fl yer designed to fl y slowly and 

gracefully. Make your turns wide (or as wide as your fl ying area will permit) and slow with control inputs early and gentle—the 
earlier you make corrections the less drastic they will have to be. Refrain from “racing” your FlyLite around the air like a 
regular sport model—most of the time it will probably be “happiest” (easiest to fl y) at approximately 1/8 or 1/4-throttle. 

Once you have the FlyLite under control adjust the trims to get it to fl y straight-and-level. You should be able to fi nd equilibrium 
with your FlyLite where it cruises slowly without climbing or descending.

Crossover

If you’re a beginner, it might be best to start with a 

crossover

 pattern to avoid turning the plane toward yourself and having 

to look at it directly “head-on.” This is because when the plane is coming at you, you will have to move the rudder stick to 
the right to make the plane to turn to your left. This seeming “control reversal” is one of the primary situations that cause 
beginners to crash.

One way to avoid having to look at the model head-on is 
to turn away from it while looking over your shoulder. Then, 
your FlyLite will be traveling the same general direction you 
are holding the transmitter.

When the FlyLIte is coming
at you, you can turn away
from the plane looking over
your shoulder.

Содержание FlyLite

























Отзывы: