GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 45 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

Operating Instructions

41

2018-06-18

Table of Contents

195-441M

Marker Operation

Optional markers are equipped with a double-selector
valve, on the tongue near the hitch, to combine the
box-fold circuit with the marker circuit. On a 2-outlet
tractor, there is a second selector valve, for the lift
circuits, mounted above the marker/fold selector.

Refer to Figure 38

After drill is unfolded for field operation, move
double-selector valve handle from forward fold position

to marker circuit (back

). Before operating markers,

make sure they are properly bled as described in
“

Bleeding Hydraulics

” on page 68.

Single Marker Operations

To operate a single marker, activate tractor remote
hydraulic lever to move marker in desired direction.

Single markers are equipped with a needle valve to
control marker folding speed. Excessive folding speed
can damage markers, so adjust needle valve to a safe
operating speed as described under “

Marker Speed

Dual Marker Operations

Dual markers are equipped with an automatic sequence
valve to control lift sequence. Starting with both markers
up, the sequence is:

•

Activate hydraulic lever; right marker lowers while left
marker stays up.

•

Reverse hydraulic lever; right marker raises while left
marker stays up.

•

Activate hydraulic lever; left marker lowers while right
marker stays up.

•

Reverse hydraulic lever; left marker raises while right
marker stays up.

Pattern repeats.

Folding speed of dual markers is adjusted with
adjustment screws on sequence-valve body. Excessive
folding speed can damage markers, so adjust markers to
a safe folding speed as described under “

Adjustments

” on page 59.

Figure 38

Fold / Marker Selector

15550

1

2

«
...
43
44
45
46
47
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Бренд: sunjoe Страницы: 20

Бренд: Gaspardo Страницы: 196

Бренд: gala gar Страницы: 32

Бренд: Terrateck Страницы: 9

Бренд: Chapin Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды