GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 48 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Operating Instructions

44

Parking

Following these steps when parking the drill for periods
of less than 36 hours. For longer periods, see “

Parking with Drill Unfolded

1.

Remove jack from storage location on top of tongue
and pin it on post on left side of tongue as shown on
page 18. Extend jack until weight of tongue is on
jack. Leave tractor hitched for the moment.

Refer to Figure 42 and Refer to Figure 42

2.

Lower parking stands located on outer ends of drill
by unpinning keeper pin and rotating stands down.
Place a block under foot of stand if it does not
contact the ground.

3.

Lower openers and reduce hydraulic down pressure
to zero.

4.

Unplug drill hydraulic hoses and electrical lines from
tractor.

Use caution when removing the hitch pin. Slight tongue
elevation may occur, even with openers and parking stands
lowered.

5.

Remove hitch pin first, then safety chain from tractor
drawbar.



NOTE:

After unhitching the unfolded drill, the tongue may rise
above tractor-drawbar height. Lower tongue by
connecting the opener-lift circuit and pressurizing openers.

Parking with Drill Folded

1.

Raise, lock and fold drill into transport position.

2.

Park drill on a level, solid area.

3.

Remove tongue jack from its storage location on top
of tongue and pin it on post on left side of tongue as
shown on page 18. Extend jack until weight of
tongue is on jack. If ground is soft, place a board or
plate under jack to widen ground-contact area.

4.

Unplug hydraulic hoses and electrical lines from
tractor.

5.

Remove hitch pin first, then safety chain from tractor
drawbar.

Crushing Hazard:

This drill has a negative tongue weight

when unfolded and openers are raised. Lower parking stand,
lower openers and remove hydraulic down pressure before
unhitching the drill in the unfolded position. Unhitching in the
unfolded position with the openers raised could result in
sudden elevation of the tongue, causing injury or death.

Figure 42

Wing Stand Pinned Up

36269

Figure 43

Wing Stand Pinned Down

36270

«
...
46
47
48
49
50
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Бренд: Delta Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды