GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 77

Страница: 77 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

2018-06-18

Table of Contents

Index

195-441M

In-Line Filters

If the raising or lowering times of the openers slow
noticeably, check the in-line filters and clean if needed.

Refer to Figure 77

Two filters are located on one each of the down-pressure
adjustment valves. If the Point Row option is installed,
another filter is located on the third adjustment valve

Refer to Figure 78

To disassemble unscrew end cap of filter. Remove top
retaining washer and screen.

Clean filter screen with solvent and compressed air, or
replace if needed.

When reassembling put screen into filter. Place retaining
washer on top of filter and screw on end cap.

Figure 77

In-Line Filter Locations

22968

Figure 78

In-Line Filter

25187

Содержание 3S-3000-3210























































































































Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000-3210, Руководство оператора

Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды