GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 72 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Maintenance and Lubrication

68

Bleeding Hydraulics

To function properly, the hydraulics must be free of air. If
hydraulics have not been bled, they will operate with
jerky, uneven motions and could cause wings to drop
rapidly during folding or unfolding. If hydraulics were not
bled during initial implement setup or if you replace a
part in hydraulic system during the life of the drill,
complete the following procedures.

High Pressure Fluid Hazard:

Escaping fluid under pressure can penetrate the skin causing
serious injury. Avoid the hazard. Relieve pressure before
disconnecting hydraulic lines. Use a piece of paper or
cardboard, NOT BODY PARTS, to check for suspected leaks.
Wear protective gloves and safety glasses or goggles when
working with hydraulic systems. If an accident occurs, seek
immediate medical attention from a physician familiar with
this type of injury.

Crushing Hazard:

Raising openers on unfolded, unhitched drill will cause drill
tongue to rise suddenly, which could cause serious injury or
death. Be certain that drill is hitched securely to your tractor
drawbar and the safety chain is securely attached to tractor
before raising openers and unfolding drill.

Bleed only at:

JIC (Joint Industry Conference, 37



flare) or

NPT (National Pipe Thread, tapered thread) fittings.

Never bleed at:

ORB (O-Ring Boss) or
QD (Quick Disconnect coupler) fittings.

Check hydraulic fluid level in tractor reservoir and fill to
proper level. Add fluid to system as needed.



NOTE:

System capacity for entire drill is about 4

1



2

U.S.

gallons (17 liters).

Over-Torque Leak Risk:

JIC fittings do not require high torque. Excess torque causes
leaks. JIC and O-ring fittings do not require sealant.

System Contamination Risk:

Always use liquid pipe sealant when adding or replacing
(NPT) pipe-thread fittings. To avoid cracking hydraulic fittings
from over tightening, and to keep tape fragments from clogging
filters, do not use plastic sealant tape.

«
...
70
71
72
73
74
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

BRILLION SL Series

Бренд: Landoll Страницы: 62

Бренд: Jetline Страницы: 35

PROMIG EVOLUTION 501

Бренд: Kemppi Страницы: 32

Бренд: Meridian Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды