background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors               11/2010 

25 

 

Safety notes and warnings 

relating to model aircraft powered by internal-combustion engines 

 

Be  sure  to  read  right  through  the  instructions  covering  assembly  and 
operation of your model before you attempt to operate it for the first time. 

 

These  safety  notes  are  an  integral  part  of  the  instructions.  Please  keep 
them and the operating instructions in a safe place. If you ever dispose of 
the model be sure to pass them on to the new owner. 

 

Powered  model  aircraft  are  very  demanding  and  potentially  dangerous 
machines,  and  call  for  a  high  level  of  technical  knowledge  and  skill  from 
the operator, together with a responsible attitude. 

 

Powered model aircraft are not suitable for young persons under eighteen 
years of age. 

 

Young  people  should  only  be  permitted  to  operate  this  model  under  the 
instruction  and  supervision  of  an  adult  who  is  aware  of  the  hazards 
involved in this activity. 

 

The  operator  of  the  model  must  be  in  full  possession  of  his  or  her  bodily 
and mental faculties.  As with car driving, operating a model aircraft under 
the  influence  of  alcohol  or  drugs  is  not  permissible  under  any 
circumstances. 

 

Radio-controlled  model  aircraft  may  only  be  employed  for  the  purpose 
intended  by  the  manufacturer.  They  must  never  be  used  as  man-carrying 
machines. Any other use of this model is prohibited. 

 

A  radio-controlled  model  aircraft  can  only  work  properly  and  fulfil  your 
expectations if it is built very carefully and in accordance with the building 
instructions.  Do  not  make  any  modifications  of  any  kind  to  the  design 
features  or  materials.  If  you  wish  to  avoid  injuring  people  and  damaging 
property  it  is  essential  to  be  careful  and  painstaking  at  all  stages  of 
building  and  operating  your  model.  Nobody  would  climb  into  a  full-size 
light  aircraft  and  try  to  fly  it  without  completing  a  course  of  training  first. 
Model  flying  is  a  skill  which  has  to  be  learned  in  just  the  same  way.  We 
suggest  that  you  ask  for  help  from  an  experienced  model  flyer,  or  join  a 
model  club  or  flight  training  school.  Your  local  model  shop  and  the 
specialist magazines are excellent sources of information. 

 

It is fundamentally essential to set the Centre of Gravity (C.G.) and control 
surface travels correctly. Adjust the model until they are exactly correct. 

 

Radio control system: satisfy yourself that your frequency is vacant before 
you  switch  on.  Check  your  RC  system  regularly  as  its  components 
eventually  wear  and  need  to  be  replaced  or  repaired.  Radio  interference 
caused by unknown sources can occur at any time without warning. If this 
should  happen,  your  model  will  be  uncontrollable  and  completely 
unpredictable.  Never  leave  your  radio  control  system  unguarded,  as  other 
people  might  pick  it  up  and  try  to  use  it.  Your  RC  system  can  only  work 
reliably if the batteries are kept fully charged. 

 

Don’t ignore our warnings. They refer to materials and situations which, if 
ignored, can result in fatal injury or permanent damage. 

 

You  alone  are  responsible  for  the  safe  operation  of  your  radio-controlled 
model aircraft and engine. 

Содержание jodel robin dr 400/18































Отзывы: