background image

GRAUPNER/SJ GmbH   D-73230 KIRCHHEIM/TECK   GERMANY 

Modifications reserved. No liability for printing errors.  

 

       02/2014 

10

 

potential accident. Model aeroplanes must always give way to full-size aircraft. Take-off and 
landing strips should be kept free of people and other obstacles. 
Your HoTT COMPUTER RC system can only work reliably if the batteries are kept fully charged. 
Never use hot, faulty or damaged batteries. It is important to observe the instructions supplied 
by the battery manufacturer. 
 
Please don’t misunderstand the purpose of these notes. We only want to make you aware of 
the many dangers and hazards which can arise if you lack knowledge and experience, or work 
carelessly or irresponsibly. Provided that you take reasonable care, model flying is a highly 
creative, instructive, enjoyable and relaxing pastime. 
 
Manufacturer’s declaration: 
If material defects or manufacturing faults should arise in a product distributed by us in the 
Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner/SJ 
GmbH, D-73230 Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects 
within the limitations described below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in the 
usability of the product is due to natural wear, use under competition conditions, incompetent 
or improper use (including incorrect installation) or external influences. 
This manufacturer’s declaration does not affect the consumer’s legal or contractual rights 
regarding defects arising from the purchase contract between the consumer and the vendor 
(dealer). 
 
Extent of the guarantee 
If a claim is made under guarantee, we undertake at our discretion to repair or replace the 
defective goods. We will not consider supplementary claims, especially for reimbursement of 
costs relating to the defect (e.g. installation / removal costs) and compensation for consequent 
damages unless they are allowed by statute. This does not affect claims based on legal 
regulations, especially according to product liability law. 
 
Guarantee requirements 
The purchaser is required to make the guarantee claim in writing, and must enclose original 
proof of purchase (e.g. invoice, receipt, delivery note) and this guarantee card. The purchaser 
must send the defective goods to us at his own cost, using the address stated above. 
The purchaser should state the material defect or manufacturing fault, or the symptoms of the 
fault, in as accurate a manner as possible, so that we can check if our guarantee obligation is 
applicable. 
The goods are transported from the consumer to us and from us to the consumer at the risk of 
the consumer. 
 
Duration of validity 
This declaration only applies to claims made to us during the claim period as stated in this 
declaration. The claim period is 24 months from the date of purchase of the product by the 
consumer from a dealer in the Federal Republic of Germany (purchase date). If a defect arises 
after the end of the claim period, or if the evidence or documents required according to this 
declaration in order to make the claim valid are not presented until after this period, then the 
consumer forfeits any rights or claims from this declaration. 
 
Limitation by lapse of time 
If we do not acknowledge the validity of a claim based on this declaration within the claim 
period, all claims based on this declaration are barred by the statute of limitations after six 
months from the time of implementation; however, this cannot occur before the end of the 
claim period. 
 
Applicable law 
This declaration, and the claims, rights and obligations arising from it, are based exclusively 
on the pertinent German Law, excluding the norms of international private law, and excluding 
UN retail law. 
 
 

Содержание HoTT Deluxe 9932.100











Отзывы: