GRAUPNER Falcon 12 plus Скачать руководство пользователя страница 15

Страница: 15 / 34

15 / 34

S1038_Q06_V1.0pn_en

"Telemetry" menu

SETTING & DATA VIEW

The basic handling of the "Telemetry" menu is described in the

respective transmitter instructions or the instructions of the Smart-

Box. By way of derogation, only in certain receivers the menu struc-

ture is summarized under the generic term "setting & data view".

These instructions also provide information on how to access this

menu. Change accordingly to the first setting page of the

Graupner

S1038 AIO FC

Notes

• The setting values shown in the following display illustrations

always show the standard values.

• Some of the menu items shown in the following display illustra-

tions are only displayed if the GPS module No. 33602 is con-

nected.

Receiver display

LANGUAGE

RECEIVER Q.06

ALARM VOLT:    10.2V
ALARM TEMP:     70°C
Altitude max:   100m

LANGUAGE: english

PERIOD: 20ms
SUMD at CH5: No

CH5: SERVO

Ant1 99% Ant2 98%

Video Channel R3
VTX-Power 0

CH6: SERVO

In the "Language" line you can set the display language in the receiver

menu.
The choices are: German, English, French, Italian, Spanish

Ant1 and Ant2

The percentages behind "Ant1" and "Ant2" indicate how high the

receive power is in percent of the respective antenna.
The display is mainly used to find the correct position of the anten-

nas during the installation.

ALARM VOLT

If the receiver voltage falls below the set value, a low-voltage warn-

ing is generated by the transmitter in the form of a "sound-declining

alarm tone" or the "receiver voltage" speech output message.

ALARM TEMP

If the receiver temperature exceeds the set temperature, a warning

is generated by the transmitter in the form of a "3-step sound-climb-

ing alarm tone" or the "receiver temperature" speech output mes-

sage.

Max. altitude

If the copter exceeds the set max. height, the transmitter emits a

warning message "max. height". Transmitters without voice output

will output a corresponding tone sequence. In autopilot mode, fur-

ther climbing is automatically prevented.

Telemetry

SETTING & DATA VIEW
SENSOR
RF STATUS VIEW
VOICE TRIGGER
RX DATA ON
ALARM SETTING

RECEIVER Q.06

ALARM VOLT: 10.2V

ALARM TEMP: 70°C

Altitude max: 100m

LANGUAGE: english

PERIOD: 20ms

SUMD at CH5: No

CH5: SERVO

Ant1 99% Ant2 98%

Video Channel R3

V T X-Power 0

CH6: SERVO

Содержание Falcon 12 plus



































Результаты поиска

Содержание Falcon 12 plus

Отзывы:

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12 plus, Руководство пользователя

Результаты поиска

Содержание Falcon 12 plus

Отзывы:

Бренды по названию

Популярные бренды